On Sun, 23 Nov 2014 08:46:25 +0100
Alexander Graf
Am 23.11.2014 um 06:37 schrieb lists
: On Sat, 22 Nov 2014 14:25:31 -0800 lists
wrote: On Sun, 23 Nov 2014 01:09:20 +0400 "Matwey V. Kornilov"
wrote: 2014-11-23 0:00 GMT+03:00 Zack Piper
: On Sun, Nov 23, 2014 at 12:50:44AM +0400, Matwey V. Kornilov wrote:
2014-11-22 23:44 GMT+03:00 Zack Piper
: > The BeagleBone Black JeOS image, I have not been using the boot > switch button, I have tried it, no LEDs lightup. Which version? 13.1 13.2 Factory?
> Another qustion, does the openSUSE image automatically activate > a tty-over-USB at all?
No
-- With best regards, Matwey V. Kornilov http://blog.matwey.name xmpp://0x2207@jabber.ru Oops, sorry, I am using 13.2.
Hm, I've tried this couple hours ago, it worked. However, first boot takes several minutes.
Is there a guide on enabling tty-over-USB?
It is disabled in config, I don't know why.
I see a new image (26.3 of JEOS 13,2) has been uploaded. I'm downloading it now, will flog it and report my findings. Note there is no sha256 for the download.
However just to be clear, on rev 26.2, the USB was totally not functional. It would not recognize usb devices plugged into it. lsusb only detected the usb chip on the SBC,
There is some confusion on the interwebs about which serial cable to get. I can say the FTDI one from Adafruit works fine. But the ethernet connection worked on the initial installation, so if somebody got lucky, they wouldn't need the serial cable. You would be installing the OS in the blind, which is why I mentioned luck.
The 26.3 rev has issues. The serial port doesn't work well. This problem wasn't evident in the 26.2 rev. USB still doesn't work.
Looks like it's working to me ;). The serial port issues usually come from a loose cable. If you press against the serial pin connectors they should go away.
Alex
I have a SD card with Debian and it works just great on the serial port. No hardware problems on my end. I just loaded Angstrom. Serial output at the end of the message. Are you using JEOS? I find the serial port failing to display characters on the JEOS 13.2 rev 26.3. The data is sent, but don't get echoed. b6a02182988f24e7260e5989f3d498e26ed53afd16219c29e2921beb5cd5ff85 openSUSE-13.2-ARM-JeOS-beaglebone.armv7l-1.12.1-Build26.3.raw.xz Here is the clean Angstrom output on the serial port. =================================================== Starting kernel ... Uncompressing Linux...latform dat-BONELT-HDMIN:00A0 (pr 0.451594]21 (gpio-leds.8) status -22 [ 0.535464] 1 on device830e000.fb: timeout waiting for framedone [ 6.6453lebone logiC-Flasher: clean, 12814/218592 files, 167134/873534 blocks CCCCCCCCCCCSoftConn) m1 max ep, 16384/16384 mipheral modeyn FIFOs, HftConn) musroller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse M270840 bytes read in 76from mmc ..c0 ... Image Name: Load Af80000, end T-HDMI) [ tion [ LT-HDMIN:00A0 (prio 2)[ 0.528136] pinctrl-single 44e10800.pinmux[ 0.904563] tilcdc 4830e000.fb: timeout waiting for framedone systemd-fsck[86]: eMMC-Flasher: clean, 12816/218592 files, 167742/873534 blocks [ 602.051133] tilcdc 4830e000.fb: timeout waiting for framedone [ 1626.087616] tilcdc 4830e000.fb: timeout waiting for framedone -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org