On Sunday 22 July 2007 14:35:07 Rajko M. wrote:

On Saturday 21 July 2007 22:24, you wrote: .... OK Rajko, I am going to trim this post quite a bit. All read over several times and thoroughly digested. I hope that won't mess you up. I will confine it to providing information and questions.

OK, ran ls /sys/bus/i2c/devices/9191-0290 and the following was listed in that directory. bob@EasyStreet:~> ls /sys/bus/i2c/devices/9191-0290 alarms fan3_div in2_max in8_input temp1_max_hyst beep_enable fan3_input in2_min in8_max temp1_type beep_mask fan3_min in3_input in8_min temp2_input bus hwmon:hwmon0 in3_max name temp2_max driver in0_input in3_min power temp2_max_hyst fan1_div in0_max in4_input pwm1 temp2_type fan1_input in0_min in4_max pwm2 temp3_input fan1_min in1_input in4_min pwm3 temp3_max fan2_div in1_max in7_input subsystem temp3_max_hyst fan2_input in1_min in7_max temp1_input temp3_type fan2_min in2_input in7_min temp1_max uevent bob@EasyStreet:~> As you can see....there is no vrm and I guess is not compiled in andsensors-s will never see it.

In both cases it is easier to write sensors.conf from scratch than to correct driver source code.

********************************************************************* Now back to proposal for sensors.conf:

*** We have raw values ***

*** We have default statements ***

*** We have what BIOS tells ***

*** We have your original posting ***

*** We have standard voltages ***

*** Missing *** We don't have sensors output with default values.

Not absolutely sure but I think my first posting was from the default values.

*** Here is attempt to wite new config file with provided data. New section name, as you don't have the other chip: chip "w83627thf-*" # Voltage section label in0 "VCore" set in0_min 1.50 # below 1.5 set in0_max 1.56 # just in case that voltage goes up

label in1 "+3.3V" set in1_min 3.14 # 3.3*0.95 set in1_max 3.47 # 3.3*1.05

label in3 "+5V" compute in3 1.667*@, @/1.667 # ((34/51)+1)=1.667

ignore in2 # for now set to ignore 0.45V

label in4 "+12V" # this usually +12 pin compute in4 3.8*@, @/3.8 # ((28/10)+1)=3.8 set in4_min 11.40 set in4_max 12.60

ignore in5 ignore in6 ignore in7

# Fan section

label fan1 "Sys Fan" label fan2 "CPU Fan" ignore fan3

# Temperature section

set sensor1 3435 # see [1] label temp1 "CPU Temp" # set temp1_over ?? # see [2] # set temp1_hyst ?? # see [2]

set sensor2 3435 # see [1] label temp2 "M/B Temp" # set temp2_over ?? # see [2] # set temp2_hyst ?? # see [2]

ignore temp3

*********************************************************************

OK I cut and pasted your suggested/trial parameters into the one line sensors.conf and ran sensors -s. (as root) Got another error: EasyStreet:/ # sensors -s Error: Line 4: Invalid keyword General parse error I looked at until my eyes glazed over. I can't see it. Here are the first few lines from your suggested conf that reportedly contains the error: chip "w83627thf-*" # Voltage section         label in0 "VCore"       set in0_min 1.50     # below 1.5         set in0_max 1.56     # just in case that voltage goes up     label in1 "+3.3V"       set in1_min 3.14     # 3.3*0.95       set in1_max 3.47     # 3.3*1.05

[1] In todays computers it is probably thermistor and temperature value will be different than for diode. The only difference can be thermistor Beta value. The 3435 is from examples sensors, but values can be changed to get same reading as BIOS: CPU 55 degrees C Sys Tmp 45 degrees C I guess that when you change sensor type to thermistor it will show proper CPU temperature. If sensors -s reports "Unknown feature name" than something is wrong.

[2] For temperature limits and hysteresis we need exac tCPU model and datasheet.

OK, we haven't got that far yet. Thanks again Bob S -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org