[opensuse] Re: MCE: The hardware reports a non fatal,...
Rajko M. wrote:
Overheating? Core voltage to low? I have one motherboard where BIOS is setting core voltage to low and CPU can't run at max bus speed.
Not seams that. See the parameters I got after two hours running: CPU Temp. : 56ºC System Temp.: 36ºC Current CPU FAN Speed: ~ 1400 rpm Current EXT FAN Speed: ~ 4618 rpm V core 1.63V 2,5V 2.47V 3,3V 3.28V 5V 4.88V 12V 11.64V Memory test (14h) gave no errors. Thanks, any way ;-) Regards, Toni -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
On Friday 21 September 2007 19:02, Toni wrote:
Not seams that. See the parameters I got after two hours running:
CPU Temp. : 56ºC System Temp.: 36ºC
Current CPU FAN Speed: ~ 1400 rpm Current EXT FAN Speed: ~ 4618 rpm V core 1.63V 2,5V 2.47V 3,3V 3.28V 5V 4.88V 12V 11.64V
Memory test (14h) gave no errors. Thanks, any way ;-)
Bad power supply? Or it's getting too hot? I had one that drove me nuts trying to figure out what the problem was. Mike -- Powered by SuSE 10.0 Kernel 2.6.13 X86_64 KDE 3.4 Kmail 1.8 7:26pm up 36 days 22:59, 6 users, load average: 2.14, 2.28, 2.26 -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
On Friday 21 September 2007 12:02:10 pm Toni wrote:
Rajko M. wrote:
Overheating? Core voltage to low? I have one motherboard where BIOS is setting core voltage to low and CPU can't run at max bus speed.
Not seams that. See the parameters I got after two hours running:
CPU Temp. : 56ºC System Temp.: 36ºC
Current CPU FAN Speed: ~ 1400 rpm Current EXT FAN Speed: ~ 4618 rpm V core 1.63V 2,5V 2.47V 3,3V 3.28V 5V 4.88V 12V 11.64V
Memory test (14h) gave no errors. Thanks, any way ;-)
Regards, Toni
Vcore seems slightly higher, if it is reported correctly. It should be 1.6 V according to [1]. Sensors is not something that you can trust without check using other methods, like BIOS health monitor. For instance reported CPU temperature is 56 C, which is low for processor that according to [1] has temperature on die 90 C with 1.6 V core. If you didn't replaced original fan and heatsink with some better than it was delivered with a box, than there is great chance that: Vcore 1.63 V + dried out termal compound + dust in and around heatsink and fan can bring CPU in range over 90 C. Though, running 2 hours is not enough to know. The CPU load is what heats it up. For instance compiling kernel from sources can heat up CPU. What I would do is to run something like GKerllM and start compilation in console window. The next hardware piece, that might be old if it is original, is hard disk. It can have transient errors, or even permanent that show up only if certain software, or data is used. If it is in /tmp, /var, or swap area than it can occur in apparently random fashion. Running fsck, badblocks, and smartctl (see man for details) should give more information. [1] AMD Duron (TM), Processor Model 3 Data Sheet File: 23802.pdf, Chapter 5, page 19. -- Regards, Rajko. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org
participants (3)
-
Mike -
Rajko M. -
Toni