raw sense data and raw, what is it?
Hi, In 8.1 , what is the purpose of "raw" in the run-level editor? Also: I have a scsi cdrom and in the boot messages I get this: ------------------------------------------------------------------------------------------- ..sr0: CDROM (ioctl) error, command: 0x43 00 00 00 00 00 00 00 0c 40 Current sr00:00: sns = 70 3 ASC=57 ASCQ= 0 Raw sense data:0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x57 0x00 0x00 0x00 0x00 0x00 sr0: CDROM (ioctl) error, command: 0x43 00 00 00 00 00 00 00 0c 00 Current sr00:00: sns = 70 3 ASC=57 ASCQ= 0 Raw sense data:0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x57 0x00 0x00 0x00 0x00 0x00 ] ------------------------------------------------------------------------------------------- Everything seems to run OK, but was is this all about. I can't find an entry for raw in the docs. -- use Perl; #powerful programmable prestidigitation
On Sunday 06 October 2002 15.34, zentara wrote:
Hi, In 8.1 , what is the purpose of "raw" in the run-level editor?
The same as in 8.0. "raw" is a command that allows raw character access to block devices. "raw" in the run-level editor runs "raw" to set up a number of previously defined devices.
Also: I have a scsi cdrom and in the boot messages I get this: --------------------------------------------------------------------------- ---------------- ..sr0: CDROM (ioctl) error, command: 0x43 00 00 00 00 00 00 00 0c 40 Current sr00:00: sns = 70 3 ASC=57 ASCQ= 0 Raw sense data:0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x57 0x00 0x00 0x00 0x00 0x00 sr0: CDROM (ioctl) error, command: 0x43 00 00 00 00 00 00 00 0c 00 Current sr00:00: sns = 70 3 ASC=57 ASCQ= 0 Raw sense data:0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x57 0x00 0x00 0x00 0x00 0x00 ] --------------------------------------------------------------------------- ----------------
Everything seems to run OK, but was is this all about. I can't find an entry for raw in the docs.
A temporary read error. The numbers are debug output. Obviously the retry worked, otherwise it would have crashed at that point. //Anders -- 'Deserves [death]. I daresay he does. Many that live deserve death. And some that die deserve life. Can you give it to them? Then do not be too eager to deal out death in judgement. For even the very wise cannot see all ends.' --Tolkien, The Lord of the Rings
On Sun, 6 Oct 2002 19:42:43 +0200
Anders Johansson
On Sunday 06 October 2002 15.34, zentara wrote: Hi, In 8.1 , what is the purpose of "raw" in the run-level editor?
The same as in 8.0. "raw" is a command that allows raw character access to block devices. "raw" in the run-level editor runs "raw" to set up a number of previously defined devices.
ASC=57 ASCQ= 0 Raw sense data:0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x57 0x00 0x00 0x00 0x00 0x00 ] ---------------------------------------------------------------------------
A temporary read error. The numbers are debug output. Obviously the retry worked, otherwise it would have crashed at that point.
//Anders
Thanks. It was a mistake on my part, I forgot I left a blank cd in there. The messages dissappear with it empty or with good cds in there. While I have your attention Anders, what do you think would cause a 30 sec delay before DNS starts resolving on a dialup account? I've tried everything and I'm stumped. I hav'nt found anything on google about delayed dns. It works fine after about 30 seconds. If I boot the same setup with my old 7.2, dns works instantly. So I'm guessing that versions 8+ have some other neccessary configuration file? Thanks for any input. -- use Perl; #powerful programmable prestidigitation
On Sunday 06 October 2002 16.16, zentara wrote:
While I have your attention Anders, what do you think would cause a 30 sec delay before DNS starts resolving on a dialup account? I've tried everything and I'm stumped. I hav'nt found anything on google about delayed dns. It works fine after about 30 seconds. If I boot the same setup with my old 7.2, dns works instantly. So I'm guessing that versions 8+ have some other neccessary configuration file?
Does the network continue to run slowly or is it just the startup that's slow? I had a problem with the newer 2.4.19 kernels in that they've started using a new acpi code, and according to Hubert Mantel this is used in 8.1 too. What would happen is that the networc card would continuously timeout. I wouldn't get a dhcp response for over a minute. On his suggestion I added "pci=acpi" on the lilo boot line as a kernel parameter and after that, everything works perfectly. I have a brand new machine. For older hardware you could try "acpi=off" and see if that improves matters. //Anders -- 'Deserves [death]. I daresay he does. Many that live deserve death. And some that die deserve life. Can you give it to them? Then do not be too eager to deal out death in judgement. For even the very wise cannot see all ends.' --Tolkien, The Lord of the Rings
On Sunday 06 October 2002 20.25, Anders Johansson wrote: <snip a load of bollocks> Ignore that. I just noticed you were talking about a dialup account. No I can't imagine what the problem is, and since I have neither 8.1 nor a dialup I can't test it either. I can only suggest you turn on the debug option in /etc/ppp/options and check the output in /var/log/messages /Anders
participants (2)
-
Anders Johansson
-
zentara