Thank you, now Capi 2.0 works. But now I have another problem: I want to use Capisuite to receive fax. Sometimes it works fine and sometimes I don't get a fax and this error in the capisuite.log: Mon Oct 31 01:09:04 2005 Connection 0x736d90: Connection object created for incoming call PLCI 201 from - to 12345 CIP 0x4 Mon Oct 31 01:09:04 2005 Connection 0x736d90: call from - to 12345 for christian connecting with fax Mon Oct 31 01:09:04 2005 Connection 0x736d90: accepting with service 1 Mon Oct 31 01:10:01 2005 Connection 0x736d90: disconnect initiated Mon Oct 31 01:10:01 2005 Connection 0x736d90: connection lost with cause 0x3400,0x3311 Mon Oct 31 01:10:02 2005 Connection 0x736d90: Connection object deleted I took a look at the capisuite manual: The code 0x3400 means that the ISDN protocol is ok and the transmission terminated normally. But the error code 0x3311 says that the connection was not successful and the remote station is not a G3 fax device?? On Suse 9.2 it worked with the same hardware. What's wrong in Opensuse 10? Has anybody an answer? Thanks. Christian

Am Mittwoch 26 Oktober 2005 10:28 schrieb Christian Präger :

...

I want to use the AVM Fritz Card PCI 2.0 with Opensuse 10 on an AMD Athlon64. This ISDN card runs perfect with the HiSAX-Driver, but if I want to use the Capi-Driver I get following error code: ... How can I get Capi work under Opensuse?

Hi Christian,

try ftp://ftp.gwdg.de/pub/linux/suse/ftp.suse.com/suse/x86_64/10.0/SUSE-Linux10.0-GM-Extra/suse/x86_64/kernel-default-nongpl-2.6.13-15.x86_64.rpm

-- mdc

--------------------------------------------------------------------- To unsubscribe, e-mail: opensuse-unsubscribe@opensuse.org For additional commands, e-mail: opensuse-help@opensuse.org

meister@netz00.com schrieb:

Am Montag 31 Oktober 2005 13:59 schrieb Christian Praeger :

...

now Capi 2.0 works. But now I have another problem: I want to use Capisuite to receive fax. Sometimes it works fine and sometimes I don't get a fax and this error in the capisuite.log: ... I took a look at the capisuite manual: The code 0x3400 means that the ISDN protocol is ok and the transmission terminated normally. But the error code 0x3311 says that the connection was not successful and the remote station is not a G3 fax device??

Hi Christian,

is it really a G3 (analog usual) fax? Or is it G4 (ISDN unusual, because too expensive)?

Yes, the sender is a normal analog faxdevice.

...

On Suse 9.2 it worked with the same hardware. What's wrong in Opensuse 10?

What did you select in YaST HylaFAX or CAPI2.0 (9.3 and 10.0)?

I used in Suse 9.x the Capi interface and in 10.0 too. Christian

Hi, if I send a fax from a ISDN card the fax is ok. Has the Capi 2.0 driver any problems with G3 faxes? Christian

Hi Christian,

is it really a G3 (analog usual) fax? Or is it G4 (ISDN unusual, because too expensive)?

...

On Suse 9.2 it worked with the same hardware. What's wrong in Opensuse 10?

What did you select in YaST HylaFAX or CAPI2.0 (9.3 and 10.0)?

-- mdc

--------------------------------------------------------------------- To unsubscribe, e-mail: opensuse-unsubscribe@opensuse.org For additional commands, e-mail: opensuse-help@opensuse.org