Hi Got some problem with my networkcard and the 2.4 kernel after installing SuSE Linux 7.1. The network-card (RPTI Plug & Play Ethernet card ISA) works fine with Kernel 2.2.18, but when I start 2.4.0 I get this message: Setting up network device eth0 insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: insmod eth0 failed SIOCSIFADDR: No such device insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: insmod eth0 failed eth0: unknown interface: No such device insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: insmod eth0 failed SIOCSIFBRDADDR: No such device insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: insmod eth0 failed eth0: unknown interface: No such device insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: insmod eth0 failed SIOCSIFNETMASK: No such device done Setting up routing (using /etc/route.conf) Error while excuting: /sbin/route add default gw 192.168.0.10 dev eth0 SIOCADDRT: No such device Setting up routing failed I've tried to install the "k_deflt_24-2.4.2-4.i386.rpm", but now Linux doesn't start at all. I just get the message: "Loading Linux_2.4.................EBDA too big." and everything stops. What can I do?? /Jonas
On Friday 09 March 2001 02:48, Jonas Söderholm wrote:
Hi
Got some problem with my networkcard and the 2.4 kernel after installing SuSE Linux 7.1. The network-card (RPTI Plug & Play Ethernet card ISA) works fine with Kernel 2.2.18, but when I start 2.4.0 I get this message:
Setting up network device eth0 insmod: /lib/modules/2.4.0-4GB/kernel/drivers/net/ne.o: init_module: No such device or address
I am not sure that it helps, but I had a similar problem with a Realtek card -- recognized under 2.2.18, but not 2.4.0. Reason: the module was renamed under 2.4. Take a look at: http://sdb.suse.de/en/sdb/html/mjb_rtl8139_24.html and do a search for your card... As for the kernel 2.4.2 that you installed, did you re-run lilo? mk_initrd (if necessary)? and depmod -a? Hope it helps, _____________ Alvaro Novo SuSE 7.1 -=- Kernel 2.4.2-4 -=- KDE 2.1 11:29pm up 5:27, 4 users, load average: 0.12, 0.10, 0.11
participants (2)
-
Jonas Söderholm -
Álvaro A. Novo