Using version 8.0 Professional How do I get the system to reconize the new port? At startup, scanning for new hardware pauses for a while, and it sees the additional serial ports (2) on the card, but not the parallel port, which is a IEEE 1284 EPP/ECP unit. Any help is appreciated. works fine under W$98. TIA Harry G
On Tue, 29 Oct 2002 16:06:49 -0500
Harry G
Using version 8.0 Professional
How do I get the system to reconize the new port? At startup, scanning for new hardware pauses for a while, and it sees the additional serial ports (2) on the card, but not the parallel port, which is a IEEE 1284 EPP/ECP unit.
Any help is appreciated. works fine under W$98.
Maybe it's conflicting with the motherboard's lpt port address? Is there a jumper on your board to select the address? Check your lp port address in your bios, and change it to an alternate. -- use Perl; #powerful programmable prestidigitation
On Tue October 29 2002 7:26 pm, zentara wrote:
On Tue, 29 Oct 2002 16:06:49 -0500
Harry G
wrote: Using version 8.0 Professional
How do I get the system to reconize the new port? At startup, scanning for new hardware pauses for a while, and it sees the additional serial ports (2) on the card, but not the parallel port, which is a IEEE 1284 EPP/ECP unit.
Any help is appreciated. works fine under W$98.
Maybe it's conflicting with the motherboard's lpt port address? Is there a jumper on your board to select the address? Check your lp port address in your bios, and change it to an alternate.
If it was conflicting, wouldn't there be problems under W$? Harry G
On Wed, 30 Oct 2002 12:28 pm, Harry G wrote:
On Tue, 29 Oct 2002 16:06:49 -0500
Harry G
wrote: Using version 8.0 Professional
How do I get the system to reconize the new port? At startup, scanning for new hardware pauses for a while, and it sees the additional serial ports (2) on the card, but not the parallel port, which is a IEEE 1284 EPP/ECP unit.
Any help is appreciated. works fine under W$98.
If it was conflicting, wouldn't there be problems under W$?
Harry G
Hi Harry, Have a look in /etc/modules.conf and you should see something like the following and add the appropiate details. alias parport_lowlevel parport_pc # options parport_pc io=0x378 irq=none,none # If you have multiple parallel ports, specify them this way: # options parport_pc io=0x378,0x278 irq=none,none Regards, Graham Smith ---------------------------------------------------------
On Tue October 29 2002 9:00 pm, Graham Smith wrote:
On Wed, 30 Oct 2002 12:28 pm, Harry G wrote:
On Tue, 29 Oct 2002 16:06:49 -0500
Harry G
wrote: Using version 8.0 Professional
How do I get the system to reconize the new port? At startup, scanning for new hardware pauses for a while, and it sees the additional serial ports (2) on the card, but not the parallel port, which is a IEEE 1284 EPP/ECP unit.
Any help is appreciated. works fine under W$98.
If it was conflicting, wouldn't there be problems under W$?
Harry G
Hi Harry,
Have a look in /etc/modules.conf and you should see something like the following and add the appropiate details.
alias parport_lowlevel parport_pc # options parport_pc io=0x378 irq=none,none # If you have multiple parallel ports, specify them this way: # options parport_pc io=0x378,0x278 irq=none,none
That is in there. Harry G
participants (3)
-
Graham Smith
-
Harry G
-
zentara