Alexandr Malusek wrote:

"S. Bulterman" writes:

...

Philip Burness wrote:

...

I'm using kernel 2.4.2 and I have a scsi cd writer & an ATAPI cd writer (hdb), I have set lilo to append hdb=ide-scsi. My normal scsi cd writer is addressed as /dev/scd0 and works OK, anybody know what address I should use to connect the ATAPI cd writer now?

...

...

cdrecord -scanbus Cdrecord 1.9 (i686-suse-linux) Copyright (C) 1995-2000 Jörg Schilling Linux sg driver version: 3.1.17 Using libscg version 'schily-0.1' scsibus0: 0,0,0 0) 'HP ' 'CD-Writer+ 9100 ' '1.0b' Removable CD-ROM 0,1,0 1) * ... 0,7,0 7) *

It has already been mentioned here that the information is in /var/log/messages:

...: scsi0 : SCSI host adapter emulation for IDE ATAPI devices ...: Vendor: HP Model: CD-Writer+ 9100 Rev: 1.0b ...: Type: CD-ROM ANSI SCSI revision: 02 ...: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 ...: sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray

Have you loaded the driver for your scsi controller? From the looks of the above, you just loaded the scsi emulator. Run "cdrecord --scanbus" again, the order in which the devices appear is the order in which you have to refer to the devices, /dev/scd0, /dev/scd1, etc. -- Rafael

Hello again Thanks for the replys. I just tried the command hwclock --systohc Then after rebooting the time was correct . It seems to have fixed it , I will check tomorrow after being shutdown overnight, hopefully the fix will take. Thanks again for tips, and replies. John WM On Mon, 28 May 2001, Alexandr Malusek wrote:

"S. Bulterman" writes:

...

Philip Burness wrote:

...

I'm using kernel 2.4.2 and I have a scsi cd writer & an ATAPI cd writer (hdb), I have set lilo to append hdb=ide-scsi. My normal scsi cd writer is addressed as /dev/scd0 and works OK, anybody know what address I should use to connect the ATAPI cd writer now?

...

Try "cdrecord --scanbus"....... And it should name every available scsi resource.

It doesn't help:

...

cdrecord -scanbus Cdrecord 1.9 (i686-suse-linux) Copyright (C) 1995-2000 Jörg Schilling Linux sg driver version: 3.1.17 Using libscg version 'schily-0.1' scsibus0: 0,0,0 0) 'HP ' 'CD-Writer+ 9100 ' '1.0b' Removable CD-ROM 0,1,0 1) * ... 0,7,0 7) *

It has already been mentioned here that the information is in /var/log/messages:

...: scsi0 : SCSI host adapter emulation for IDE ATAPI devices ....: Vendor: HP Model: CD-Writer+ 9100 Rev: 1.0b ....: Type: CD-ROM ANSI SCSI revision: 02 ....: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 ....: sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray

The device is /dev/sr0 in my case. "..." stands for omitted information.

-- Alexandr.Malusek@imv.liu.se

-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq and the archives at http://lists.suse.com