Re: [SLE] hard disk failure or???? URGENT
CE>The 03.10.05 at 01:11, Constant Brouerius van Nidek
CE>wrote:
CE>> What bothers me is that I have to rewrite the fstab
CE>because
CE>> it is practically empty.
CE>That's a file you should keep a printed copy on paper,
CE>together with the
CE>partition list and exact sizes.
CE>> And what about the mtab?
CE>Nothing :-)
CE>--
CE>Cheers,
Dear Carlos
Rewrote my fstab and rebooted. Same information as before
showed up and looking at the fstab it was reduced to the
former three lines.
Would hate to do a new install but cannot find what is
further missing. I have the boot.log on which I see that
before entering into runlevel 3 everything is fine,
After that there is a lot of
info which I could not decifer. It is in the attachment.
--
Cannot find map file.
Loaded 396 symbols from 15 modules.
klogd 1.4.1, log source = ksyslog started.
<4>Linux version 2.4.20-4GB (root@Pentium.suse.de) (gcc version 3.3 20030226 (prerelease) (SuSE Linux)) #1 Mon Mar 17 17:54:44 UTC 2003
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<4>Scanning bios EBDA for MXT signature
<5>0MB HIGHMEM available.
<5>256MB LOWMEM available.
<7>ACPI: have wakeup address 0xc0001000
<4>On node 0 totalpages: 65536
<4>zone(0): 4096 pages.
<4>zone(1): 61440 pages.
<4>zone(2): 0 pages.
<5>ACPI disabled because your bios is from 99 and too old
<5>You can enable it with acpi=force
<4>Building zonelist for node : 0
<4>Kernel command line: BOOT_IMAGE=linux SuSE=,12
07200100,0AA44FA0., initrd=initrd ramdisk_size=65536 rescue=1 vga=0x31a
<6>Initializing CPU#0
<4>Detected 400.915 MHz processor.
<4>Console: colour dummy device 80x25
<4>Calibrating delay loop... 799.53 BogoMIPS
<6>Memory: 250824k/262144k available (1569k kernel code, 10932k reserved, 574k data, 160k init, 0k highmem)
<6>Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
<6>Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 512K
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
<7>CPU: Common caps: 0183f9ff 00000000 00000000 00000000
<4>CPU: Intel Pentium II (Deschutes) steppi
ng 03
<6>Enabling fast FPU save and restore... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>ACPI: Subsystem revision 20030228
<6>ACPI: Disabled via command line (acpi=off)
<6>PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
<6>PCI: Using configuration type 1
<6>PCI: Probing PCI hardware
<4>PCI: ACPI tables contain no PCI IRQ routing entries
<4>PCI: Probing PCI hardware (bus 00)
<6>Limiting direct PCI/PCI transfers.
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
<4>mxt_scan_bios: enter
<4>Starting kswapd
<4>bigpage subsystem: allocated 0 bigpages (=0MB).
<4>kinoded started
<5>VFS: Disk quotas vdquot_6.5.1
<5>aio_setup: num_physpages = 16384
<5>aio_setup: sizeof(struct page) = 48
<6>vesafb: framebuffer
at 0xe0000000, mapped to 0xd080d000, size 16384k
<6>vesafb: mode is 1280x1024x16, linelength=2560, pages=5
<6>vesafb: protected mode interface info at c000:7f4d
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<6>Looking for splash picture.... found (1280x1024, 32818 bytes, v3).
<4>Console: switching to colour frame buffer device 148x51
<6>fb0: VESA VGA frame buffer device
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>Real Time Clock Driver v1.10e
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
<6>loop: loaded (max 16 devices)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>PIIX4: I
DE controller at PCI slot 00:07.1
<6>PIIX4: chipset revision 1
<6>PIIX4: not 100%% native mode: will probe irqs later
<6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
<6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
<4>hda: ST34313A, ATA DISK drive
<4>hdb: ST34321A, ATA DISK drive
<4>blk: queue c03ac0c0, I/O limit 4095Mb (mask 0xffffffff)
<4>blk: queue c03ac214, I/O limit 4095Mb (mask 0xffffffff)
<4>hdc: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive
<4>hdd: Seagate Technology 1275MB - ST31276A, ATA DISK drive
<4>blk: queue c03ac694, I/O limit 4095Mb (mask 0xffffffff)
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>hda: 8452080 sectors (4327 MB) w/512KiB Cache, CHS=526/255/63, UDMA(33)
<4>hdb: attached ide-disk driver.
<4>hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
<4>hdb: task_no_data_intr: error=0x04 { DriveStatusEr
ror }
<6>hdb: 8404830 sectors (4303 MB) w/128KiB Cache, CHS=523/255/63, UDMA(33)
<4>hdd: attached ide-disk driver.
<4>hdd: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
<4>hdd: task_no_data_intr: error=0x04 { DriveStatusError }
<6>hdd: 2502308 sectors (1281 MB), CHS=2482/16/63, DMA
<4>ide-floppy driver 0.99.newide
<6>Partition check:
<6> hda: hda1 hda2 hda3 hda4
<6> hdb: hdb1
<6> hdd: hdd1
<4>ide-floppy driver 0.99.newide
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 2048 buckets, 16Kbytes
<6>TCP: Hash tables configured (established 16384 bind 32768)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<
5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 4973k freed
<4>VFS: Mounted root (minix filesystem).
<4>ide-floppy driver 0.99.newide
<6>Non-volatile memory driver v1.2
<4>hdc: attached ide-cdrom driver.
<4>hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
<6>Uniform CD-ROM driver Revision: 3.12
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<4>end_request: I/O error, dev 02:00 (floppy), sector 0
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<6>usb-uhci.c: $Revision: 1.275 $ time 18:24:43 Mar 17 2003
<6>usb-uhci.c: High bandwidth mode enabled
<6>usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 10
<4>usb-uhci.c: Detected 2 ports
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<6>usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
<6>hub.c: new USB device 00:07.2-1, assigned address 2
<4>usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any
active driver.
<6>usb.c: registered new driver hiddev
<6>usb.c: registered new driver hid
<6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
The 03.10.05 at 12:15, Constant Brouerius van Nidek wrote:
Rewrote my fstab and rebooted. Same information as before showed up and looking at the fstab it was reduced to the former three lines.
Er... impossible. Are you editing your HD fstab, or trying to edit the rescue system fstab? If you edit the later, your system is not modified...
Would hate to do a new install but cannot find what is further missing. I have the boot.log on which I see that before entering into runlevel 3 everything is fine, After that there is a lot of info which I could not decifer. It is in the attachment.
The file has line wrapping, perhaps done by your editor, so it is very difficult to read - I had to go over it several times to see things. I see you have problems with your hdb HD. <6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA <6> ide1: BM-DMA at0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA <4>hda: ST34313A, ATA DISK drive <4>hdb: ST34321A, ATA DISK drive ... <4>hdc: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive <4>hdd: Seagate Technology 1275MB - ST31276A, ATA DISK drive ... <4>hda: attached ide-disk driver. <4>hda: host protected area => 1 <6>hda: 8452080 sectors (4327 MB) w/512KiB Cache, CHS=526/255/63, UDMA(33) <4>hdb: attached ide-disk driver. <4>hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error } <4>hdb: task_no_data_intr: error=0x04 { DriveStatusError } <6>hdb: 8404830 sectors (4303 MB) w/128KiB Cache, CHS=523/255/63, UDMA(33) The kernel has problems talking to your second hard disk. It is set to UDMA at 33 Mhz, slow for modern times - but your systems is PII, so it could be normal. 4 Gb, is that correct? <4>hdd: attached ide-disk driver. <4>hdd: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error } <4>hdd: task_no_data_intr: error=0x04 { DriveStatusError } <6>hdd: 2502308 sectors (1281 MB), CHS=2482/16/63, DMA and also to your fourth device. <6>Partition check: <6> hda: hda1 hda2 hda3 hda4 <6> hdb: hdb1 <6> hdd: hdd1 Mmmm... both devices (b and d) have only one partition detected. Is that correct? <5>RAMDISK: Compressed image found at block 0 <6>Freeing initrd memory: 4973k freed <4>VFS: Mounted root (minix filesystem). Your initial ramdisk is minix. Funny. <4>VFS: Mounted root (ext2 filesystem) readonly. Did you check your cables? Did you reseat them? Perhaps even replace one of them, to see what happens. Perhaps you could try to disable DMA for those two disks. -- Cheers, Carlos Robinson
participants (2)
-
Carlos E. R.
-
Constant Brouerius van Nidek