I have just done a fresh install of SuSE 8.2 to replace my 3 -NIC firewall box. Stuff I expected in /etc has been moved but found. Shorewall installation through YAST removes Kernel Sources, but I can NOT figure out the #$%^&&% ! Routing changes. I have/had a working /etc/route.conf & /etc/rc.config I now kind of find what I need in /etc/sysconfig/network/ifcfg-n & /etc/sysconfig/network/routing How do I fill in the correct "blanks" YAST certainly doesn't seem to help for multiple NIC's with different routing - the very purpose that I have the multiple NIC's! Can someone steer me in the right direction ? Required - eth0 to a single 192.x.x.x NIC (Primary Firewall) eth1 to my network 192.x.x.x (Samba PDC, Windoze boxes, CUPS printers) eth2 to another private single 10.x.x.x - Bill
On Thursday 08 May 2003 19:10 pm, Bill.Light@kp.org wrote:
I have just done a fresh install of SuSE 8.2 to replace my 3 -NIC firewall box.
Stuff I expected in /etc has been moved but found. Shorewall installation through YAST removes Kernel Sources, but I can NOT figure out the #$%^&&% ! Routing changes.
I have/had a working /etc/route.conf & /etc/rc.config I now kind of find what I need in /etc/sysconfig/network/ifcfg-n & /etc/sysconfig/network/routing
How do I fill in the correct "blanks" YAST certainly doesn't seem to help for multiple NIC's with different routing - the very purpose that I have the multiple NIC's!
Not sure how much I can help with words, but this should be a piece of cake and YAST can do it. You configure each nic with the proper IP address, and routing. I've done it with two but three shouldn't be any different. I'm no network whiz but I had no problem with it. Just let YAST do it... Forget what you had before.
Can someone steer me in the right direction ?
Required - eth0 to a single 192.x.x.x NIC (Primary Firewall) eth1 to my network 192.x.x.x (Samba PDC, Windoze boxes, CUPS printers) eth2 to another private single 10.x.x.x
- Bill
-- +----------------------------------------------------------------------------+ + Bruce S. Marshall bmarsh@bmarsh.com Bellaire, MI 05/08/03 19:56 + +----------------------------------------------------------------------------+ "A lack of leadership is no substitute for inaction."
Bill, Things got changed around from 7.3 -> 8.0, 8.1, 8.2 to be LSB compliant. This will be more like redhat with all the relevant stuff now found in etc/sysconfig/network Interfaces are all ifcfg-eth*, routing can be set in the routes file All this can still be done through yast/2, but if you are going to have aliased interfaces, the best thing to do is copy ifcfg-eth0 say to ifcfg-eth0:1 and vi the file and make your changes. Hope this helps. James
-----Original Message----- From: Bill.Light@kp.org [mailto:Bill.Light@kp.org] Sent: Thursday, May 08, 2003 5:11 PM To: suse-linux-e@suse.com Subject: [SLE] Routing - 7.3 versus 8.x
I have just done a fresh install of SuSE 8.2 to replace my 3 -NIC firewall box.
Stuff I expected in /etc has been moved but found. Shorewall installation through YAST removes Kernel Sources, but I can NOT figure out the #$%^&&% ! Routing changes.
I have/had a working /etc/route.conf & /etc/rc.config I now kind of find what I need in /etc/sysconfig/network/ifcfg-n & /etc/sysconfig/network/routing
How do I fill in the correct "blanks" YAST certainly doesn't seem to help for multiple NIC's with different routing - the very purpose that I have the multiple NIC's!
Can someone steer me in the right direction ?
Required - eth0 to a single 192.x.x.x NIC (Primary Firewall) eth1 to my network 192.x.x.x (Samba PDC, Windoze boxes, CUPS printers) eth2 to another private single 10.x.x.x
- Bill
participants (3)
-
Bill.Light＠kp.org -
Bruce Marshall -
Deiknumi Lists