hallo miteinander, in einen unserer server wollte ich eine kingston kne100tx karte einbauen. der kernel erkennt die karte wunderbar (ist eth2), auch sonst scheint alles i.O: # dmesg ... tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov eth0: Digital DS21140 Tulip at 0xd400, 00 c0 f0 1f 79 65, IRQ 11. eth0: EEPROM default media type Autosense. eth0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth0: MII transceiver found at MDIO address 1, config 3000 status 782d. eth0: Advertising 01e1 on PHY 1, previously advertising 01e1. eth1: Digital DS21140 Tulip at 0xd800, 00 c0 f0 1f 79 87, IRQ 12. eth1: EEPROM default media type Autosense. eth1: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth1: MII transceiver found at MDIO address 1, config 3000 status 782d. eth1: Advertising 01e1 on PHY 1, previously advertising 01e1. eth2: Digital DS21142/3 Tulip at 0xdc00, 00 c0 f0 4c 2d b9, IRQ 5. eth2: EEPROM default media type Autosense. eth2: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. eth2: MII transceiver found at MDIO address 1, config 3000 status 7829. eth2: Advertising 01e1 on PHY 1, previously advertising 01e1. ... # ifconfig eth2 eth2 Link encap:10Mbps Ethernet HWaddr 00:C0:F0:4C:2D:B9 inet addr:192.168.1.5 Bcast:192.1.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:1 dropped:0 overruns:0 TX packets:0 errors:0 dropped:0 overruns:0 Interrupt:5 Base address:0xdc00 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 212.254.210.128 0.0.0.0 255.255.255.128 U 0 0 3 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 19 eth0 leider geht nicht mal ein ping auf eine andere maschine, z.b. 192.168.1.7 der hub meldet einen fehler... ich vermute eine problem mit dem autosensing des hubs und autosensing von der eth2 karte. frage: wie kann ich der karte beim lilo (in /etc/lilo.conf) die option mitgeben, dass sie sich direkt auf 100Tx einstellt? danke fuer alle antworten jan --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Jan Stifter wrote:
hallo miteinander,
Hi Jan.
... frage: wie kann ich der karte beim lilo (in /etc/lilo.conf) die option mitgeben, dass sie sich direkt auf 100Tx einstellt? Weiss nicht, ob Du das via lilo kannst (schau dazu mal ins Ethernet-Howto, da sind imho auch Tools fuer sowas erwaehnt).
Vielleicht kannst Du aber die (vermutlich vom Hersteller mitgelieferten) Tools verwenden (falls Du jemanden kennst, der Dir mal eine DOS-Diskette borgt). Damit solltest Du imho an das BIOS der Karte rankommen. Rgds. Heiko. -- Nuetzliche Samba-Doku online: http://de.samba.org/samba/docs/ --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Hi Jan,
hallo miteinander, in einen unserer server wollte ich eine kingston kne100tx karte einbauen. der kernel erkennt die karte wunderbar (ist eth2), auch sonst scheint alles i.O:
# dmesg ... tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov eth0: Digital DS21140 Tulip at 0xd400, 00 c0 f0 1f 79 65, IRQ 11. eth0: EEPROM default media type Autosense. eth0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth0: MII transceiver found at MDIO address 1, config 3000 status 782d. eth0: Advertising 01e1 on PHY 1, previously advertising 01e1. eth1: Digital DS21140 Tulip at 0xd800, 00 c0 f0 1f 79 87, IRQ 12. eth1: EEPROM default media type Autosense. eth1: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth1: MII transceiver found at MDIO address 1, config 3000 status 782d. eth1: Advertising 01e1 on PHY 1, previously advertising 01e1. eth2: Digital DS21142/3 Tulip at 0xdc00, 00 c0 f0 4c 2d b9, IRQ 5. eth2: EEPROM default media type Autosense. eth2: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. eth2: MII transceiver found at MDIO address 1, config 3000 status 7829. eth2: Advertising 01e1 on PHY 1, previously advertising 01e1. ...
# ifconfig eth2 eth2 Link encap:10Mbps Ethernet HWaddr 00:C0:F0:4C:2D:B9 inet addr:192.168.1.5 Bcast:192.1.1.255 Mask:255.255.255.0
Der Broadcast sollte 192.168.1.255 sein
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:1 dropped:0 overruns:0 TX packets:0 errors:0 dropped:0 overruns:0 Interrupt:5 Base address:0xdc00
# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 212.254.210.128 0.0.0.0 255.255.255.128 U 0 0 3 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 19 eth0
leider geht nicht mal ein ping auf eine andere maschine, z.b. 192.168.1.7
der hub meldet einen fehler... ich vermute eine problem mit dem autosensing des hubs und autosensing von der eth2 karte.
frage: wie kann ich der karte beim lilo (in /etc/lilo.conf) die
option
mitgeben, dass sie sich direkt auf 100Tx einstellt?
ich kenn die Karte zwar nicht, aber die meisten Karten die ich kenne, können über ein tool vom Hersteller, auf einer bootbaren dosdiskette von 10Mbps auf 100Mbps oder auf autosensing eingestellt werden. Es mag sein das Deine Karte auf 10Mbps steht. by Joerg --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Jörg Zimmermann schrieb in 2,8K (77 Zeilen): [Vorredner bitte leben lassen]
der hub meldet einen fehler... ich vermute eine problem mit dem autosensing des hubs und autosensing von der eth2 karte.
kenne, können über ein tool vom Hersteller, auf einer bootbaren dosdiskette von 10Mbps auf 100Mbps oder auf autosensing eingestellt werden. Es mag sein das Deine Karte auf 10Mbps steht.
Und/oder auf full-duplex. Hub ==> Halbduplex. -Wolfgang --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
participants (4)
-
heiko.degenhardt@sentec-elektronik.de
-
j.stifter@medres.ch
-
j.zimmermann@xsiteing.de
-
weissel@netcologne.de