Hallo, nach Umstellung meine Soundunterstützung von OSS->Soundmodul bekomme ich folgende Kernelmeldungen: Siehe Zeile mit == beginnend Ich benutze eine Daytona von TB. Die Karte läuft unter Windows einwandfrei und mit OSS auch. Abgesehen von diesen Meldungen, die bestimmt nicht in Ordnung sind, kommen auch jetzt Sounds aus der Karte heraus. Aber wie gesagt, richtig scheint es ja nicht zu sein... Inspecting /boot/System.map-2.2.13 Loaded 8602 symbols from /boot/System.map-2.2.13. Symbols match kernel version 2.2.13. Loaded 30 symbols from 4 modules. klogd 1.3-3, log source = ksyslog started. <4>Linux version 2.2.13 (root@meinpc) (gcc version 2.95.2 19991024 (release)) #16 Sun Mar 12 11:12:59 Local time zone must be set--see zic manual page 2000 <4>Detected 167048500 Hz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 333.41 BogoMIPS <4>Memory: 95576k/98304k available (1032k kernel code, 412k reserved, 1224k data, 60k init, 0k bigmem) <4>DENTRY hash table entries: 16384 (order: 5, 131072 bytes) <4>Buffer-cache hash table entries: 131072 (order: 7, 524288 bytes) <4>Page-cache hash table entries: 32768 (order: 5, 131072 bytes) <4>CPU: AMD AMD-K6tm w/ multimedia extensions stepping 01 <6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting. <6>Checking 'hlt' instruction... OK. <6>AMD K6 stepping B detected - <6>K6 BUG 20058008 20000000 (Report these if test report is incorrect) <6>AMD K6 stepping B detected - system stability may be impaired when more than 32 MB are used. <6>Please see http://www.mygale.com/~poulot/k6bug.html <4>POSIX conformance testing by UNIFIX <4>PCI: PCI BIOS revision 2.10 entry at 0xfb530 <4>PCI: Using configuration type 1 <4>PCI: Probing PCI hardware <4>PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00) <6>Activating ISA DMA hang workarounds. <6>Linux NET4.0 for Linux 2.2 <6>Based upon Swansea University Computer Society NET3.039 <6>NET4: Unix domain sockets 1.0 for Linux NET4.0. <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <4>Initializing RT netlink socket <4>Starting kswapd v 1.5 <6>Detected PS/2 Mouse Port. <4>pty: 256 Unix98 ptys configured <6>Real Time Clock Driver v1.09 <4>RAM disk driver initialized: 16 RAM disks of 64000K size <6>Uniform Multi-Platform E-IDE driver Revision: 6.20 <4>VP_IDE: IDE controller on PCI bus 00 dev 39 <4>VP_IDE: not 100% native mode: will probe irqs later <4>VT 82C585 Apollo VP1/VPX Chipset Core ATA-33 <4>Split FIFO Configuration: 16 Primary buffers, threshold = 3/4 <4> 0 Second. buffers, threshold = 1/2 <4> ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:pio, hdb:pio <4>ide0: VIA Bus-Master (U)DMA Timing Config Success <4>hda: IBM-DTTA-351010, ATA DISK drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <6>hda: IBM-DTTA-351010, 9671MB w/466kB Cache, CHS=1232/255/63, (U)DMA <4>scsi0 : AdvanSys SCSI 3.2F: PCI Ultra 16 CDB: IO 6100/F, IRQ 12 <4>scsi : 1 host. <4> Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 <4> Type: CD-ROM ANSI SCSI revision: 02 <4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 <4> Vendor: SEAGATE Model: ST39140N Rev: 1444 <4> Type: Direct-Access ANSI SCSI revision: 02 <4>Detected scsi disk sda at scsi0, channel 0, id 3, lun 0 <4>scsi : detected 1 SCSI cdrom 1 SCSI disk total. <6>Uniform CDROM driver Revision: 2.56 <4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB] <4>Partition check: <4> sda: sda1 < sda5 > sda2 sda3 <4> hda: hda1 hda2 < hda5 > <4>VFS: Mounted root (ext2 filesystem) readonly. <4>Freeing unused kernel memory: 60k freed <6>Adding Swap: 136544k swap-space (priority -1) <6>sv: version v0.21 time 11:00:03 Mar 12 2000 ==<6>sv: BIOS did not allocate DDMA channel A io, allocated at 0xac00 ==<6>sv: BIOS did not allocate DDMA channel C io, allocated at 0xac10 ==<7>sv: io ports: 0x6300 0x6400 0x6500 0x6600 0x6700 0xac00 0xac10 ==<6>sv: found adapter at io 0x6400 irq 5 dmaa 0xac00 dmac 0xac10 ==revision 3 ==<7>sv: DMA buffer crosses 64k boundary: busaddr 0x360000 size 131072 Kernel logging (ksyslog) stopped. Kernel log daemon terminating. -- Tschau ;-) jens --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com