Welche Kernel-Parameter f. Parallel-Port-Druck
Mit meinem selbstgebauten 2.4.21-rc7-grsec kann ich nicht mehr mit einem Lexmark-Postscript-Laser E322 drucken. Was habe ich denn da übersehen? # grep PARPORT .config CONFIG_PARPORT=y CONFIG_PARPORT_PC=y CONFIG_PARPORT_PC_CML1=y # CONFIG_PARPORT_SERIAL is not set # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_PC_PCMCIA is not set # CONFIG_PARPORT_AMIGA is not set # CONFIG_PARPORT_MFC3 is not set # CONFIG_PARPORT_ATARI is not set # CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_SUNBPP is not set # CONFIG_PARPORT_OTHER is not set # CONFIG_PARPORT_1284 is not set Al
* On Fri, 13 Jun 2003 at 13:53 +0200, Al Bogner wrote:
Mit meinem selbstgebauten 2.4.21-rc7-grsec kann ich nicht mehr mit einem Lexmark-Postscript-Laser E322 drucken.
Was habe ich denn da übersehen?
# grep PARPORT .config CONFIG_PARPORT=y CONFIG_PARPORT_PC=y CONFIG_PARPORT_PC_CML1=y # CONFIG_PARPORT_SERIAL is not set # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_PC_PCMCIA is not set # CONFIG_PARPORT_AMIGA is not set # CONFIG_PARPORT_MFC3 is not set # CONFIG_PARPORT_ATARI is not set # CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_SUNBPP is not set # CONFIG_PARPORT_OTHER is not set # CONFIG_PARPORT_1284 is not set
CONFIG_PRINTER=y ? /apm -- GPG welcome, request public key: mailto:adalbert+key@lopez.at
On Friday 13 June 2003 14:02, Adalbert Michelic wrote:
Mit meinem selbstgebauten 2.4.21-rc7-grsec kann ich nicht mehr mit einem Lexmark-Postscript-Laser E322 drucken.
Was habe ich denn da übersehen?
CONFIG_PRINTER=y ?
Danke, ich habe in letzter Zeit wohl zuviele Vanilla-Kernel konfiguriert und das übersehen. Al
Hallo, On Fri, 13 Jun 2003, Adalbert Michelic wrote:
* On Fri, 13 Jun 2003 at 13:53 +0200, Al Bogner wrote:
Mit meinem selbstgebauten 2.4.21-rc7-grsec kann ich nicht mehr mit einem Lexmark-Postscript-Laser E322 drucken.
Was habe ich denn da übersehen?
# grep PARPORT .config CONFIG_PARPORT=y CONFIG_PARPORT_PC=y CONFIG_PARPORT_PC_CML1=y # CONFIG_PARPORT_SERIAL is not set # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set [..] # CONFIG_PARPORT_1284 is not set
CONFIG_PRINTER=y ?
CONFIG_PARPORT_1284 sollte aber auch aktiviert werden, dass ermoeglicht die bidirektionale Kommunikation nach IEEE-1284. CONFIG_PARPORT_1284: If you have a printer that supports status readback or device ID, or want to use a device that uses enhanced parallel port transfer modes such as EPP and ECP, say Y here to enable advanced IEEE 1284 transfer modes. Also say Y if you want device ID information to appear in /proc/sys/dev/parport/*/autoprobe*. It is safe to say N. Ich habe bei mir ausserdem PARPORT_PC_FIFO und PARPORT_PC_SUPERIO aktiviert... -dnh --
Leider Gottes ist es so, daß wenn man einen Spammer zu Strecke gebracht hat, dafür drei neue auftauchen. Das ist wie bei den Fliegen. Schlägst Du eine Tot, kommen 40 zur Beerdigung. ;) [> Martin Mewes und Michael Raab in suse-linux]
participants (3)
-
Adalbert Michelic
-
Al Bogner
-
David Haller