Am Donnerstag, 4. Juli 2002 16:01 schrieb Karsten Keil:
On Thu, Jul 04, 2002 at 02:40:25PM +0200, Jürgen Fahnenschreiber wrote:
Hallo!
Ich habe eine AVM B1-Karte (vermutl. Jahrgang 97). Wie krieg ich die jetzt unter Suse 7.3, Kernel 2.4.19pre10 zum Laufen? Die Treiber von der AVM -Page gehen nur bis Kernel 2.4.10 Der B1 -Treiber ist fest im Kernel drinnen. Capi habe ich als Modul im Kernel.
Du brauchst garnichts von AVM, die Karte seit 2.0.X immer im kernel unterstuetzt, allerdings sollte man immer Module verwenden, direkt im Kernel funktioniert nicht immer. Wenn ich mich über kinternet einwählen will, klappt das nicht. Ich krieg folgende Meldung in der /var/log/messages
Jul 4 16:48:59 linux kernel: ippp0: dialing 1 0192071... Jul 4 16:49:06 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 16:49:06 linux kernel: NETDEV WATCHDOG: ippp0: transmit timed out Jul 4 16:49:06 linux kernel: isdn_tx_timeout dev ippp0 dialstate 4 Jul 4 16:49:08 linux kernel: isdn_net: local hangup ippp0 Jul 4 16:49:08 linux kernel: ippp0: Chargesum is 0 Gruß, Jürgen
Hallo!
Ich habe eine AVM B1-Karte (vermutl. Jahrgang 97). Wie krieg ich die jetzt unter Suse 7.3, Kernel 2.4.19pre10 zum Laufen? Die Treiber von der AVM -Page gehen nur bis Kernel 2.4.10 Der B1 -Treiber ist fest im Kernel drinnen. Capi habe ich als Modul im Kernel.
Du brauchst garnichts von AVM, die Karte seit 2.0.X immer im kernel unterstuetzt, allerdings sollte man immer Module verwenden, direkt im Kernel funktioniert nicht immer.
Wenn ich mich über kinternet einwählen will, klappt das nicht. Ich krieg folgende Meldung in der /var/log/messages
Jul 4 16:48:59 linux kernel: ippp0: dialing 1 0192071... Jul 4 16:49:06 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 16:49:06 linux kernel: NETDEV WATCHDOG: ippp0: transmit timed out Jul 4 16:49:06 linux kernel: isdn_tx_timeout dev ippp0 dialstate 4 Jul 4 16:49:08 linux kernel: isdn_net: local hangup ippp0 Jul 4 16:49:08 linux kernel: ippp0: Chargesum is 0 Jürgen
In der SDB habe ich einen Artikel zum einrichten der AVM B1 unter Suse 6.1 bis 6.3 gefunden. Ich habe zwar die 7.3 aber denoch existieren folgende Dateien nicht: /etc/rc.config.d/i4l_b1.rc.config /etc/rc.config.d/i4l_default.rc.config /etc/rc.config.d/i4l_hisax.rc.config Brauche ich die nicht mehr? Ist das jetzt woanders? Gruß, Jürgen
On Thu, Jul 04, 2002 at 04:52:02PM +0200, Jürgen Fahnenschreiber wrote:
Am Donnerstag, 4. Juli 2002 16:01 schrieb Karsten Keil:
On Thu, Jul 04, 2002 at 02:40:25PM +0200, Jürgen Fahnenschreiber wrote:
Hallo!
Ich habe eine AVM B1-Karte (vermutl. Jahrgang 97). Wie krieg ich die jetzt unter Suse 7.3, Kernel 2.4.19pre10 zum Laufen? Die Treiber von der AVM -Page gehen nur bis Kernel 2.4.10 Der B1 -Treiber ist fest im Kernel drinnen. Capi habe ich als Modul im Kernel.
Du brauchst garnichts von AVM, die Karte seit 2.0.X immer im kernel unterstuetzt, allerdings sollte man immer Module verwenden, direkt im Kernel funktioniert nicht immer. Wenn ich mich über kinternet einwählen will, klappt das nicht. Ich krieg folgende Meldung in der /var/log/messages
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ? -- Karsten Keil SuSE Labs ISDN development
Am Donnerstag, 4. Juli 2002 17:24 schrieb Karsten Keil:
On Thu, Jul 04, 2002 at 04:52:02PM +0200, Jürgen Fahnenschreiber wrote:
Am Donnerstag, 4. Juli 2002 16:01 schrieb Karsten Keil:
On Thu, Jul 04, 2002 at 02:40:25PM +0200, Jürgen Fahnenschreiber
wrote:
Hallo!
Ich habe eine AVM B1-Karte (vermutl. Jahrgang 97). Wie krieg ich die jetzt unter Suse 7.3, Kernel 2.4.19pre10 zum Laufen? Die Treiber von der AVM -Page gehen nur bis Kernel 2.4.10 Der B1 -Treiber ist fest im Kernel drinnen. Capi habe ich als Modul im Kernel.
Du brauchst garnichts von AVM, die Karte seit 2.0.X immer im kernel unterstuetzt, allerdings sollte man immer Module verwenden, direkt im Kernel funktioniert nicht immer.
Wenn ich mich über kinternet einwählen will, klappt das nicht. Ich krieg folgende Meldung in der /var/log/messages
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ? Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2" # Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001" # # Subtype of a given type # I4L_SUBTYPE_1="1" # # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1="" # # Membase if any # I4L_MEMBASE_1="" # # IO address if any # I4L_IO_1="" # # IO0 (ISA PnP) # I4L_IO0_1="" # # IO1 (ISA PnP) # I4L_IO1_1="" # # IO2 (ISA PnP) # I4L_IO2_1="" # # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1="" # # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1="" # # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1="" I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2="" Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden. Jürgen
Hi, On Thu, Jul 04, 2002 at 05:34:20PM +0200, Jürgen Fahnenschreiber wrote: ... Hier ist die AVM 2 mal eingetragen, loesche mal den 2. Eintrag.
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ?
Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001"
# # Subtype of a given type # I4L_SUBTYPE_1="1"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1=""
# # Membase if any # I4L_MEMBASE_1=""
# # IO address if any # I4L_IO_1=""
# # IO0 (ISA PnP) # I4L_IO0_1=""
# # IO1 (ISA PnP) # I4L_IO1_1=""
# # IO2 (ISA PnP) # I4L_IO2_1=""
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1=""
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1=""
Ab hier loeschen:
I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2=""
Erstmal nur eine B1 configurieren und die Fritz weglassen (kann im Rechner bleiben). System neustarten. Sicherstellen, das die B1 auch am S0 haengt.
Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden.
-- Karsten Keil SuSE Labs ISDN development
Hier ist die AVM 2 mal eingetragen, loesche mal den 2. Eintrag.
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ?
Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001"
# # Subtype of a given type # I4L_SUBTYPE_1="1"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1=""
# # Membase if any # I4L_MEMBASE_1=""
# # IO address if any # I4L_IO_1=""
# # IO0 (ISA PnP) # I4L_IO0_1=""
# # IO1 (ISA PnP) # I4L_IO1_1=""
# # IO2 (ISA PnP) # I4L_IO2_1=""
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1=""
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1=""
Ab hier loeschen:
I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2=""
Erstmal nur eine B1 configurieren und die Fritz weglassen (kann im Rechner bleiben). System neustarten. Sicherstellen, das die B1 auch am S0 haengt.
Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden. S0 -Was ist das? Es funktioniert leider immer noch nicht. Bei einem erneuten Versuch, krieg ich folgende Meldungen in der /var/log/messages:
Jul 4 20:12:00 linux last message repeated 6 times Jul 4 20:12:02 linux kernel: ippp0: dialing 1 0192071... Jul 4 20:12:09 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:11 linux kernel: isdn_net: local hangup ippp0 Jul 4 20:12:11 linux kernel: ippp0: Chargesum is 0 Jul 4 20:12:18 linux kernel: ippp2: dialing 1 07118949099... Jul 4 20:12:25 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:26 linux kernel: isdn_net: local hangup ippp2 Jul 4 20:12:26 linux kernel: ippp2: Chargesum is 0 Jul 4 20:12:29 linux kernel: NETDEV WATCHDOG: ippp0: transmit timed out Jul 4 20:12:29 linux kernel: isdn_tx_timeout dev ippp0 dialstate 0 Jul 4 20:12:29 linux kernel: isdn_net: ippp0: dial rejected: interface not in dialmode `auto', signalling dst_link_failure Hier ist mal ein Auszug aus der /var/log/boot: <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 <6>dss1_divert module successfully installed <6>HiSax: Linux Driver for passive ISDN cards <6>HiSax: Version 3.5 (kernel) <6>HiSax: Layer1 Revision 1.1.4.1 <6>HiSax: Layer2 Revision 1.1.4.1 <6>HiSax: TeiMgr Revision 1.1.4.1 <6>HiSax: Layer3 Revision 1.1.4.1 <6>HiSax: LinkLayer Revision 1.1.4.1 <6>HiSax: Approval certification valid <6>HiSax: Approved with ELSA Microlink PCI cards <6>HiSax: Approved with Eicon Technology Diva 2.01 PCI cards <6>HiSax: Approved with Sedlbauer Speedfax + cards <6>HiSax: Approved with HFC-S PCI A based cards <7>HiSax: Total 1 card defined <6>HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) <6>HiSax: AVM PCI driver Rev. 1.1.4.1 <6>AVM PCI: stat 0x3020a <6>AVM PCI: Class A Rev 2 <6>HiSax: AVM Fritz!PCI config irq:10 base:0xCC00 <6>AVM PCI: ISAC version (0): 2086/2186 V1.1 <6>AVM Fritz PnP/PCI: IRQ 10 count 0 <6>AVM Fritz PnP/PCI: IRQ 10 count 3 <6>HiSax: DSS1 Rev. 1.1.4.1 <6>HiSax: 2 channels added <6>HiSax: MAX_WAITING_CALLS added <5>isdnloop-ISDN-driver Rev 1.1.4.1 <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <6>IP: routing cache hash table of 2048 buckets, 16Kbytes <6>TCP: Hash tables configured (established 16384 bind 16384) <6>Linux IP multicast router 0.06 plus PIM-SM <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <5>RAMDISK: Compressed image found at block 0 <6>Freeing initrd memory: 666k freed Mir ist gerade noch etwas aufgefallen. Bei ippp0 habe ich die B1 als Hardware angegeben (mit yast1). Wenn ich aber einfach das Kabel von der B1 in die FritzCard umstecke, dann komme ich sofort ins Internet! Also muss da irgendwo schon der Fehler legen. Hoffentlich kannst Du damit etwas anfangen. Gruß, Jürgen
On Thu, Jul 04, 2002 at 08:20:44PM +0200, Jürgen Fahnenschreiber wrote:
Hier ist die AVM 2 mal eingetragen, loesche mal den 2. Eintrag.
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ?
Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001"
# # Subtype of a given type # I4L_SUBTYPE_1="1"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1=""
# # Membase if any # I4L_MEMBASE_1=""
# # IO address if any # I4L_IO_1=""
# # IO0 (ISA PnP) # I4L_IO0_1=""
# # IO1 (ISA PnP) # I4L_IO1_1=""
# # IO2 (ISA PnP) # I4L_IO2_1=""
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1=""
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1=""
Ab hier loeschen:
I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2=""
Erstmal nur eine B1 configurieren und die Fritz weglassen (kann im Rechner bleiben). System neustarten. Sicherstellen, das die B1 auch am S0 haengt.
Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden. S0 -Was ist das?
S0 Bus - der ISDN Anschluss.
Es funktioniert leider immer noch nicht. Bei einem erneuten Versuch, krieg ich folgende Meldungen in der /var/log/messages:
Jul 4 20:12:00 linux last message repeated 6 times Jul 4 20:12:02 linux kernel: ippp0: dialing 1 0192071... Jul 4 20:12:09 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:11 linux kernel: isdn_net: local hangup ippp0 Jul 4 20:12:11 linux kernel: ippp0: Chargesum is 0 Jul 4 20:12:18 linux kernel: ippp2: dialing 1 07118949099... Jul 4 20:12:25 linux kernel: isdn: HiSax,ch0 cause: E001B
Das sieht so aus als ob noch immer die Fritzkarte geladen ist und diese nicht am S0 Bus angeschlossen ist ?
Hier ist mal ein Auszug aus der /var/log/boot:
<6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 <6>dss1_divert module successfully installed <6>HiSax: Linux Driver for passive ISDN cards <6>HiSax: Version 3.5 (kernel) <6>HiSax: Layer1 Revision 1.1.4.1 <6>HiSax: Layer2 Revision 1.1.4.1 <6>HiSax: TeiMgr Revision 1.1.4.1 <6>HiSax: Layer3 Revision 1.1.4.1 ... Ja HiSax wird fuer die Fritz geladen, steht da noch irgendwo was in einer anderen config Datei ?
Mach mal ein grep I4L /etc/rc.config und grep I4L /etc/rc.config.d/*
Mir ist gerade noch etwas aufgefallen. Bei ippp0 habe ich die B1 als Hardware angegeben (mit yast1). Wenn ich aber einfach das Kabel von der B1 in die FritzCard umstecke, dann komme ich sofort ins Internet! Also muss da irgendwo schon der Fehler legen.
Das ist richtig so (bis darauf das ein Treiber fuer die Fritz geladen wird), man kann den Karten kein interface direkt zuordnen, es wird immer der erste gefundene Anschluss benutzt und das ist in diesem Fall die Fritz. -- Karsten Keil SuSE Labs ISDN development
Am Donnerstag, 4. Juli 2002 20:52 schrieb Karsten Keil:
On Thu, Jul 04, 2002 at 08:20:44PM +0200, Jürgen Fahnenschreiber wrote:
Hier ist die AVM 2 mal eingetragen, loesche mal den 2. Eintrag.
Was steht denn in /etc/rc.config.d/i4l_hardware.rc.config ?
Hier steht folgendes: # # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="avm"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030 I4L_TYPE_1="8001"
# # Subtype of a given type # I4L_SUBTYPE_1="1"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1=""
# # Membase if any # I4L_MEMBASE_1=""
# # IO address if any # I4L_IO_1=""
# # IO0 (ISA PnP) # I4L_IO0_1=""
# # IO1 (ISA PnP) # I4L_IO1_1=""
# # IO2 (ISA PnP) # I4L_IO2_1=""
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1=""
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" # I4L_EAZMAP_1=""
Ab hier loeschen:
I4L_ID_2="avm2" I4L_PROTOCOL_2="2" I4L_TYPE_2="8001" I4L_SUBTYPE_2="1" I4L_IRQ_2="" I4L_MEMBASE_2="0x0" I4L_IO_2="0x0" I4L_IO0_2="0x0" I4L_IO1_2="0x0" I4L_IO2_2="0x0" I4L_MODUL_OPTIONS_2="" I4L_HISAXDEBUG_2="" I4L_EAZMAP_2=""
Erstmal nur eine B1 configurieren und die Fritz weglassen (kann im Rechner bleiben). System neustarten. Sicherstellen, das die B1 auch am S0 haengt.
Neben der B1 habe ich noch eine FritzCard PCI im Rechner. Diese funktioniert problemlos. Die B1 wird von Yast1 und Yast2 erkannt. Unter Yast1 krieg ich auch keine Fehlermeldung beim konfigurieren/ starten. Die B1 müsste also funktionieren. Mit lsmod stellte ich fest, das auch die Module für capi und für die b1 geladen wurden.
S0 -Was ist das?
S0 Bus - der ISDN Anschluss.
Es funktioniert leider immer noch nicht. Bei einem erneuten Versuch, krieg ich folgende Meldungen in der /var/log/messages:
Jul 4 20:12:00 linux last message repeated 6 times Jul 4 20:12:02 linux kernel: ippp0: dialing 1 0192071... Jul 4 20:12:09 linux kernel: isdn: HiSax,ch0 cause: E001B Jul 4 20:12:11 linux kernel: isdn_net: local hangup ippp0 Jul 4 20:12:11 linux kernel: ippp0: Chargesum is 0 Jul 4 20:12:18 linux kernel: ippp2: dialing 1 07118949099... Jul 4 20:12:25 linux kernel: isdn: HiSax,ch0 cause: E001B
Das sieht so aus als ob noch immer die Fritzkarte geladen ist und diese nicht am S0 Bus angeschlossen ist ?
Hier ist mal ein Auszug aus der /var/log/boot:
<6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 <6>dss1_divert module successfully installed <6>HiSax: Linux Driver for passive ISDN cards <6>HiSax: Version 3.5 (kernel) <6>HiSax: Layer1 Revision 1.1.4.1 <6>HiSax: Layer2 Revision 1.1.4.1 <6>HiSax: TeiMgr Revision 1.1.4.1 <6>HiSax: Layer3 Revision 1.1.4.1
... Ja HiSax wird fuer die Fritz geladen, steht da noch irgendwo was in einer anderen config Datei ?
Mach mal ein
grep I4L /etc/rc.config
und
grep I4L /etc/rc.config.d/*
Mir ist gerade noch etwas aufgefallen. Bei ippp0 habe ich die B1 als Hardware angegeben (mit yast1). Wenn ich aber einfach das Kabel von der B1 in die FritzCard umstecke, dann komme ich sofort ins Internet! Also muss da irgendwo schon der Fehler legen.
Das ist richtig so (bis darauf das ein Treiber fuer die Fritz geladen wird), man kann den Karten kein interface direkt zuordnen, es wird immer der erste gefundene Anschluss benutzt und das ist in diesem Fall die Fritz. Hier sind die Ausgaben:
linux:~ # grep I4L /etc/rc.config I4L_START="yes" linux:~ # linux:~ # grep I4L /etc/rc.config.d/* /etc/rc.config.d/i4l_hardware.rc.config:I4L_ID_1="avm" /etc/rc.config.d/i4l_hardware.rc.config:I4L_PROTOCOL_1="2" /etc/rc.config.d/i4l_hardware.rc.config:I4L_TYPE_1="8001" /etc/rc.config.d/i4l_hardware.rc.config:I4L_SUBTYPE_1="1" /etc/rc.config.d/i4l_hardware.rc.config:I4L_IRQ_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_MEMBASE_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_IO_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_IO0_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_IO1_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_IO2_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_MODUL_OPTIONS_1="" /etc/rc.config.d/i4l_hardware.rc.config:I4L_HISAXDEBUG_1="" /etc/rc.config.d/i4l_hardware.rc.config:# eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" /etc/rc.config.d/i4l_hardware.rc.config:I4L_EAZMAP_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_ID_1="avm" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_PROTOCOL_1="2" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_TYPE_1="8001" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_SUBTYPE_1="1" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IRQ_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_MEMBASE_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO0_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO1_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO2_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_MODUL_OPTIONS_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_HISAXDEBUG_1="" /etc/rc.config.d/i4l_hardware.rc.config~:# eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_EAZMAP_1="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_ID_2="avm2" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_PROTOCOL_2="2" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_TYPE_2="8001" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_SUBTYPE_2="1" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IRQ_2="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_MEMBASE_2="0x0" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO_2="0x0" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO0_2="0x0" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO1_2="0x0" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_IO2_2="0x0" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_MODUL_OPTIONS_2="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_HISAXDEBUG_2="" /etc/rc.config.d/i4l_hardware.rc.config~:I4L_EAZMAP_2="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_ID_1="avm" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_PROTOCOL_1="2" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_TYPE_1="8001" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_SUBTYPE_1="1" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_IRQ_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_MEMBASE_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_IO_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_IO0_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_IO1_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_IO2_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_MODUL_OPTIONS_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_HISAXDEBUG_1="" /etc/rc.config.d/i4l_hardware.rc.config.old:# eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" /etc/rc.config.d/i4l_hardware.rc.config.old:I4L_EAZMAP_1="" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_ID_1="HiSax" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_PROTOCOL_1="2" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_TYPE_1="27" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_SUBTYPE_1="0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_IRQ_1="" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_MEMBASE_1="0x0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_IO_1="0x0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_IO0_1="0x0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_IO1_1="0x0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_IO2_1="0x0" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_MODUL_OPTIONS_1="" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_HISAXDEBUG_1="" /etc/rc.config.d/i4l_hardware.rc.config.old.o:# eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-" /etc/rc.config.d/i4l_hardware.rc.config.old.o:I4L_EAZMAP_1="" /etc/rc.config.d/i4l.rc.config:# enable "isdnctrl verbose $I4L_VERBOSE_LEVEL" (yes or no) /etc/rc.config.d/i4l.rc.config:I4L_VERBOSE="yes" /etc/rc.config.d/i4l.rc.config:I4L_VERBOSE_LEVEL="3" /etc/rc.config.d/i4l.rc.config:I4L_IDLETIME_0="60" /etc/rc.config.d/i4l.rc.config:I4L_IDLETIME_1="360" /etc/rc.config.d/i4l.rc.config:I4L_IDLETIME_2="360" /etc/rc.config.d/i4l.rc.config:I4L_IDLETIME_3="360" /etc/rc.config.d/i4l.rc.config:I4L_DIALMAX_0="2" /etc/rc.config.d/i4l.rc.config:I4L_DIALMAX_1="0" /etc/rc.config.d/i4l.rc.config:I4L_DIALMAX_2="2" /etc/rc.config.d/i4l.rc.config:I4L_DIALMAX_3="0" /etc/rc.config.d/i4l.rc.config:I4L_LOCALMSN_0="" /etc/rc.config.d/i4l.rc.config:I4L_LOCALMSN_1="618912" /etc/rc.config.d/i4l.rc.config:I4L_LOCALMSN_2="618912" /etc/rc.config.d/i4l.rc.config:I4L_LOCALMSN_3="618913" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_OUT_0="" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_OUT_1="07118949099" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_OUT_2="08431399999" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_OUT_3="0192071" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_IN_0="" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_IN_1="" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_IN_2="" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_IN_3="" /etc/rc.config.d/i4l.rc.config:I4L_ENCAP_0="syncppp" /etc/rc.config.d/i4l.rc.config:I4L_ENCAP_1="syncppp" /etc/rc.config.d/i4l.rc.config:I4L_ENCAP_2="syncppp" /etc/rc.config.d/i4l.rc.config:I4L_ENCAP_3="syncppp" /etc/rc.config.d/i4l.rc.config:I4L_SECURE_0="on" /etc/rc.config.d/i4l.rc.config:I4L_SECURE_1="on" /etc/rc.config.d/i4l.rc.config:I4L_SECURE_2="on" /etc/rc.config.d/i4l.rc.config:I4L_SECURE_3="on" /etc/rc.config.d/i4l.rc.config:I4L_PPPBIND_0="" /etc/rc.config.d/i4l.rc.config:I4L_PPPBIND_1="" /etc/rc.config.d/i4l.rc.config:I4L_PPPBIND_2="" /etc/rc.config.d/i4l.rc.config:I4L_PPPBIND_3="" /etc/rc.config.d/i4l.rc.config:I4L_CHARGEHUP_0="off" /etc/rc.config.d/i4l.rc.config:I4L_CHARGEHUP_1="off" /etc/rc.config.d/i4l.rc.config:I4L_CHARGEHUP_2="off" /etc/rc.config.d/i4l.rc.config:I4L_CHARGEHUP_3="off" /etc/rc.config.d/i4l.rc.config:I4L_IHUP_0="off" /etc/rc.config.d/i4l.rc.config:I4L_IHUP_1="" /etc/rc.config.d/i4l.rc.config:I4L_IHUP_2="off" /etc/rc.config.d/i4l.rc.config:I4L_IHUP_3="" /etc/rc.config.d/i4l.rc.config:I4L_L2_0="hdlc" /etc/rc.config.d/i4l.rc.config:I4L_L2_1="" /etc/rc.config.d/i4l.rc.config:I4L_L2_2="hdlc" /etc/rc.config.d/i4l.rc.config:I4L_L2_3="" /etc/rc.config.d/i4l.rc.config:I4L_L3_0="trans" /etc/rc.config.d/i4l.rc.config:I4L_L3_1="" /etc/rc.config.d/i4l.rc.config:I4L_L3_2="trans" /etc/rc.config.d/i4l.rc.config:I4L_L3_3="" /etc/rc.config.d/i4l.rc.config:I4L_DIALMODE_0="auto" /etc/rc.config.d/i4l.rc.config:I4L_DIALMODE_1="manual" /etc/rc.config.d/i4l.rc.config:I4L_DIALMODE_2="manual" /etc/rc.config.d/i4l.rc.config:I4L_DIALMODE_3="manual" /etc/rc.config.d/i4l.rc.config:I4L_CALLBACK_0="off" /etc/rc.config.d/i4l.rc.config:I4L_CALLBACK_1="off" /etc/rc.config.d/i4l.rc.config:I4L_CALLBACK_2="off" /etc/rc.config.d/i4l.rc.config:I4L_CALLBACK_3="off" /etc/rc.config.d/i4l.rc.config:I4L_CBDELAY_0="2" /etc/rc.config.d/i4l.rc.config:I4L_CBDELAY_1="" /etc/rc.config.d/i4l.rc.config:I4L_CBDELAY_2="2" /etc/rc.config.d/i4l.rc.config:I4L_CBDELAY_3="" /etc/rc.config.d/i4l.rc.config:I4L_CBHUP_0="on" /etc/rc.config.d/i4l.rc.config:I4L_CBHUP_1="" /etc/rc.config.d/i4l.rc.config:I4L_CBHUP_2="on" /etc/rc.config.d/i4l.rc.config:I4L_CBHUP_3="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_0="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_1="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_2="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_3="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVEMSN_0="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVEMSN_1="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVEMSN_2="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVEMSN_3="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_OUT_0="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_OUT_1="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_OUT_2="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_OUT_3="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_IN_0="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_IN_1="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_IN_2="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_IN_3="" /etc/rc.config.d/i4l.rc.config:I4L_IDLETIME_4="60" /etc/rc.config.d/i4l.rc.config:I4L_DIALMAX_4="" /etc/rc.config.d/i4l.rc.config:I4L_LOCALMSN_4="0" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_OUT_4="010700192070" /etc/rc.config.d/i4l.rc.config:I4L_REMOTE_IN_4="" /etc/rc.config.d/i4l.rc.config:I4L_ENCAP_4="syncppp" /etc/rc.config.d/i4l.rc.config:I4L_SECURE_4="on" /etc/rc.config.d/i4l.rc.config:I4L_PPPBIND_4="" /etc/rc.config.d/i4l.rc.config:I4L_CHARGEHUP_4="off" /etc/rc.config.d/i4l.rc.config:I4L_IHUP_4="" /etc/rc.config.d/i4l.rc.config:I4L_L2_4="" /etc/rc.config.d/i4l.rc.config:I4L_L3_4="" /etc/rc.config.d/i4l.rc.config:I4L_DIALMODE_4="manual" /etc/rc.config.d/i4l.rc.config:I4L_CALLBACK_4="off" /etc/rc.config.d/i4l.rc.config:I4L_CBDELAY_4="" /etc/rc.config.d/i4l.rc.config:I4L_CBHUP_4="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_4="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVEMSN_4="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_OUT_4="" /etc/rc.config.d/i4l.rc.config:I4L_SLAVE_IN_4="" /etc/rc.config.d/i4l.rc.config.old:# enable "isdnctrl verbose $I4L_VERBOSE_LEVEL" (yes or no) /etc/rc.config.d/i4l.rc.config.old:I4L_VERBOSE="yes" /etc/rc.config.d/i4l.rc.config.old:I4L_VERBOSE_LEVEL="3" /etc/rc.config.d/i4l.rc.config.old:I4L_IDLETIME_0="60" /etc/rc.config.d/i4l.rc.config.old:I4L_IDLETIME_1="360" /etc/rc.config.d/i4l.rc.config.old:I4L_IDLETIME_2="360" /etc/rc.config.d/i4l.rc.config.old:I4L_IDLETIME_3="360" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMAX_0="2" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMAX_1="0" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMAX_2="2" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMAX_3="0" /etc/rc.config.d/i4l.rc.config.old:I4L_LOCALMSN_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_LOCALMSN_1="618912" /etc/rc.config.d/i4l.rc.config.old:I4L_LOCALMSN_2="618912" /etc/rc.config.d/i4l.rc.config.old:I4L_LOCALMSN_3="618913" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_OUT_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_OUT_1="07118949099" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_OUT_2="08431399999" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_OUT_3="0192071" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_IN_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_IN_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_IN_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_IN_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_ENCAP_0="syncppp" /etc/rc.config.d/i4l.rc.config.old:I4L_ENCAP_1="syncppp" /etc/rc.config.d/i4l.rc.config.old:I4L_ENCAP_2="syncppp" /etc/rc.config.d/i4l.rc.config.old:I4L_ENCAP_3="syncppp" /etc/rc.config.d/i4l.rc.config.old:I4L_SECURE_0="on" /etc/rc.config.d/i4l.rc.config.old:I4L_SECURE_1="on" /etc/rc.config.d/i4l.rc.config.old:I4L_SECURE_2="on" /etc/rc.config.d/i4l.rc.config.old:I4L_SECURE_3="on" /etc/rc.config.d/i4l.rc.config.old:I4L_PPPBIND_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_PPPBIND_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_PPPBIND_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_PPPBIND_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_CHARGEHUP_0="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CHARGEHUP_1="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CHARGEHUP_2="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CHARGEHUP_3="off" /etc/rc.config.d/i4l.rc.config.old:I4L_IHUP_0="off" /etc/rc.config.d/i4l.rc.config.old:I4L_IHUP_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_IHUP_2="off" /etc/rc.config.d/i4l.rc.config.old:I4L_IHUP_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_L2_0="hdlc" /etc/rc.config.d/i4l.rc.config.old:I4L_L2_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_L2_2="hdlc" /etc/rc.config.d/i4l.rc.config.old:I4L_L2_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_L3_0="trans" /etc/rc.config.d/i4l.rc.config.old:I4L_L3_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_L3_2="trans" /etc/rc.config.d/i4l.rc.config.old:I4L_L3_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMODE_0="auto" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMODE_1="manual" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMODE_2="manual" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMODE_3="manual" /etc/rc.config.d/i4l.rc.config.old:I4L_CALLBACK_0="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CALLBACK_1="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CALLBACK_2="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CALLBACK_3="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CBDELAY_0="2" /etc/rc.config.d/i4l.rc.config.old:I4L_CBDELAY_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_CBDELAY_2="2" /etc/rc.config.d/i4l.rc.config.old:I4L_CBDELAY_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_CBHUP_0="on" /etc/rc.config.d/i4l.rc.config.old:I4L_CBHUP_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_CBHUP_2="on" /etc/rc.config.d/i4l.rc.config.old:I4L_CBHUP_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVEMSN_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVEMSN_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVEMSN_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVEMSN_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_OUT_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_OUT_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_OUT_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_OUT_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_IN_0="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_IN_1="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_IN_2="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_IN_3="" /etc/rc.config.d/i4l.rc.config.old:I4L_IDLETIME_4="60" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMAX_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_LOCALMSN_4="0" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_OUT_4="010700192070" /etc/rc.config.d/i4l.rc.config.old:I4L_REMOTE_IN_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_ENCAP_4="syncppp" /etc/rc.config.d/i4l.rc.config.old:I4L_SECURE_4="on" /etc/rc.config.d/i4l.rc.config.old:I4L_PPPBIND_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_CHARGEHUP_4="off" /etc/rc.config.d/i4l.rc.config.old:I4L_IHUP_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_L2_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_L3_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_DIALMODE_4="manual" /etc/rc.config.d/i4l.rc.config.old:I4L_CALLBACK_4="off" /etc/rc.config.d/i4l.rc.config.old:I4L_CBDELAY_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_CBHUP_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVEMSN_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_OUT_4="" /etc/rc.config.d/i4l.rc.config.old:I4L_SLAVE_IN_4="" /etc/rc.config.d/i4l.rc.config.old.o:# enable "isdnctrl verbose $I4L_VERBOSE_LEVEL" (yes or no) /etc/rc.config.d/i4l.rc.config.old.o:I4L_VERBOSE="yes" /etc/rc.config.d/i4l.rc.config.old.o:I4L_VERBOSE_LEVEL="3" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IDLETIME_0="60" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IDLETIME_1="60" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IDLETIME_2="60" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IDLETIME_3="60" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMAX_0="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMAX_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMAX_2="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMAX_3="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_LOCALMSN_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_LOCALMSN_1="618907" /etc/rc.config.d/i4l.rc.config.old.o:I4L_LOCALMSN_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_LOCALMSN_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_OUT_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_OUT_1="010700192070" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_OUT_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_OUT_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_IN_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_IN_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_IN_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_REMOTE_IN_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_ENCAP_0="syncppp" /etc/rc.config.d/i4l.rc.config.old.o:I4L_ENCAP_1="syncppp" /etc/rc.config.d/i4l.rc.config.old.o:I4L_ENCAP_2="rawip" /etc/rc.config.d/i4l.rc.config.old.o:I4L_ENCAP_3="rawip" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SECURE_0="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SECURE_1="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SECURE_2="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SECURE_3="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_PPPBIND_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_PPPBIND_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_PPPBIND_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_PPPBIND_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CHARGEHUP_0="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CHARGEHUP_1="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CHARGEHUP_2="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CHARGEHUP_3="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IHUP_0="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IHUP_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IHUP_2="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_IHUP_3="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L2_0="hdlc" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L2_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L2_2="hdlc" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L2_3="hdlc" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L3_0="trans" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L3_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L3_2="trans" /etc/rc.config.d/i4l.rc.config.old.o:I4L_L3_3="trans" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMODE_0="auto" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMODE_1="manual" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMODE_2="auto" /etc/rc.config.d/i4l.rc.config.old.o:I4L_DIALMODE_3="auto" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CALLBACK_0="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CALLBACK_1="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CALLBACK_2="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CALLBACK_3="off" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBDELAY_0="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBDELAY_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBDELAY_2="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBDELAY_3="2" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBHUP_0="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBHUP_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBHUP_2="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_CBHUP_3="on" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVEMSN_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVEMSN_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVEMSN_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVEMSN_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_OUT_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_OUT_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_OUT_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_OUT_3="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_IN_0="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_IN_1="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_IN_2="" /etc/rc.config.d/i4l.rc.config.old.o:I4L_SLAVE_IN_3="" linux:~ # So. Morgen werd ich mal die FritzCard ausbauen. Vielleicht klappt's dann doch. Im Hardware-Info von Yast2 konnte ich noch folgendes finden: IRQ 10 bei beiden Karten, ebenso bei beiden count: 8720, enabled: ja, IO ist dagegen bei beiden unterschiedlich. Die B1 hat die Slot-ID 6 und die FritzCard die 7, Die B1 hat die SubID 1 und die FritzCard die SubID 0 -> Könnte es daran liegen, das die FritzCard "bevorzugt" verwendet wird? Gruß, Jürgen
Hi, On Thu, Jul 04, 2002 at 08:20:44PM +0200, Jürgen Fahnenschreiber wrote: ist mir ebend erst aufgefallen:
<6>HiSax: Version 3.5 (kernel)
Du hast den Fritz Treiber fest in den kernel compiliert, damit wird er immer als 1. Karte geladen - keine Chance fuer die B1. Nochmal: Die ISDN Treiber direkt in den Kernel compilieren bringt meistens Probleme, da alle bootscripte usw. von Modulen ausgehen (nur so kann man alle Karten unterstuetzen). Es macht nur fuer wenige ganz spezielle Anwendungen Sinn (z.B. embedded Systeme). -- Karsten Keil SuSE Labs ISDN development
participants (2)
-
Jürgen Fahnenschreiber
-
Karsten Keil