moin ich habe eine pci fritzkarte und bekomme sie bei suse7prof nicht ans laufen. ich hänge mal einige auszüge aus logfiles an. vielleicht hilt das ja weiter. ansonsten kann ich noch sagen das ich eine netzwerkkarte mit einem 10er netz beglückt habe und die isdn karte wird standartmäßig mit 192(?)er netz versorgt. kann es auch daran liegen?? danke für eure hilfe ------------------ bott.msg: Inspecting /boot/System.map-2.2.16 Loaded 9060 symbols from /boot/System.map-2.2.16. Symbols match kernel version 2.2.16. Loaded 72 symbols from 3 modules. klogd 1.3-3, log source = ksyslog started. <4>Linux version 2.2.16 (root@Pentium.suse.de) (gcc version 2.95.2 19991024 (release)) #1 Wed Aug 2 20:22:26 GMT 2000 <4>Detected 451032 kHz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 897.84 BogoMIPS <4>Memory: 256948k/262144k available (1448k kernel code, 412k reserved, 2916k data, 68k init, 0k bigmem) <4>Dentry hash table entries: 32768 (order 6, 256k) <4>Buffer cache hash table entries: 262144 (order 8, 1024k) <4>Page cache hash table entries: 65536 (order 6, 256k) <5>VFS: Diskquotas version dquot_6.4.0 initialized <4>CPU: Intel Celeron (Mendocino) stepping 00 <6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting. <6>Checking 'hlt' instruction... OK. <4>POSIX conformance testing by UNIFIX <4>mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au) <4>PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1 <4>PCI: Using configuration type 1 <4>PCI: Probing PCI hardware <6>Linux NET4.0 for Linux 2.2 <6>Based upon Swansea University Computer Society NET3.039 <6>NET4: Unix domain sockets 1.0 for Linux NET4.0. <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <4>TCP: Hash tables configured (ehash 262144 bhash 65536) <4>Initializing RT netlink socket <4>Starting kswapd v 1.5 <6>Detected PS/2 Mouse Port. <4>pty: 256 Unix98 ptys configured <6>Real Time Clock Driver v1.09 <4>RAM disk driver initialized: 16 RAM disks of 64000K size <6>loop: registered device at major 7 <6>Uniform Multi-Platform E-IDE driver Revision: 6.30 <4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <4>PIIX4: IDE controller on PCI bus 00 dev 21 <4>PIIX4: chipset revision 1 <4>PIIX4: not 100%% native mode: will probe irqs later <4> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio <4>hda: IBM-DTTA-371440, ATA DISK drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <6>hda: IBM-DTTA-371440, 13783MB w/462kB Cache, CHS=1757/255/63 <6>Floppy drive(s): fd0 is 1.44M <6>FDC 0 is a post-1991 82077 <6>LVM version 0.8e by Heinz Mauelshagen (4/1/2000) <4>lvm -- Driver successfully initialized <4>md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8 <4>linear personality registered <4>raid0 personality registered <4>raid1 personality registered <4>raid5 personality registered <4>scsi : 0 hosts. <4>scsi : detected total. <4>Partition check: <4> hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 > <5>RAMDISK: Compressed image found at block 0 <4>Uncompressing................................done. <4>VFS: Mounted root (ext2 filesystem). <6>ncr53c8xx: at PCI bus 0, device 9, function 0 <6>ncr53c8xx: 53c815 detected <6>ncr53c815-0: rev 0x4 on pci bus 0 device 9 function 0 irq 9 <6>ncr53c815-0: ID 7, Fast-10, Parity Checking <4>scsi0 : ncr53c8xx-3.4.0-20000709 <4>scsi : 1 host. <4> Vendor: TEAC Model: CD-ROM CD-532S Rev: 3.0A <4> Type: CD-ROM ANSI SCSI revision: 02 <4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0 <4> Vendor: TEAC Model: CD-R55S Rev: 1.0R <4> Type: CD-ROM ANSI SCSI revision: 02 <4>Detected scsi CD-ROM sr1 at scsi0, channel 0, id 6, lun 0 <6>ncr53c815-0-<2,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8) <4>sr0: scsi3-mmc drive: 0x/0x caddy <6>Uniform CD-ROM driver Revision: 3.11 <6>ncr53c815-0-<6,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8) <6>usb.c: registered new driver usbdevfs <6>usb.c: registered new driver hub <4>Checking ReiserFS transaction log (device 03:0a) ... <4>Using tea hash to sort names <4>ReiserFS core development sponsored by SuSE Labs (suse.com) <4>Journaling sponsored by MP3.com <4>ReiserFS version 3.5.23 <4>VFS: Mounted root (reiserfs filesystem). <4>change_root: old root has d_count=1 <5>Trying to unmount old root ... okay <4>Freeing unused kernel memory: 68k freed <6>Adding Swap: 666656k swap-space (priority -1) <6>Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled <6>ttyS00 at 0x03f8 (irq = 4) is a 16550A <6>ttyS01 at 0x02f8 (irq = 3) is a 16550A Kernel logging (ksyslog) stopped. Kernel log daemon terminating. warn: Dec 2 15:18:48 linux kernel: HiSax: AVM Fritz PnP/PCI config port b400-b41f already in use Dec 2 15:18:48 linux kernel: HiSax: Card AVM Fritz PnP/PCI not installed ! Dec 2 15:18:58 linux kernel: isapnp: Card 'Creative SB AWE64 PnP' Dec 2 15:18:58 linux kernel: isapnp: 1 Plug & Play card detected total messages: Dec 2 15:18:45 linux syslogd 1.3-3: restart. Dec 2 15:18:48 linux kernel: CAPI-driver Rev 1.18 : loaded Dec 2 15:18:48 linux kernel: capifs: Rev 1.11 : loaded Dec 2 15:18:48 linux kernel: capi20: started up with major 68 Dec 2 15:18:48 linux kernel: kcapi: capi20 attached Dec 2 15:18:48 linux kernel: capi20: Rev1.40: started up with major 68 Dec 2 15:18:48 linux kernel: fcpci: AVM FRITZ!Card PCI driver, revision 0.0 Dec 2 15:18:48 linux kernel: fcpci: Loading... Dec 2 15:18:48 linux kernel: fcpci: Driver 'fcpci' attached to stack Dec 2 15:18:48 linux kernel: kcapi: driver fcpci attached Dec 2 15:18:48 linux kernel: fcpci: Auto-attaching... Dec 2 15:18:48 linux kernel: fcpci: Stack version 3.09-02 Dec 2 15:18:48 linux kernel: kcapi: Controller 1: fritz-pci attached Dec 2 15:18:48 linux kernel: kcapi: card 1 "fritz-pci" ready. Dec 2 15:18:48 linux kernel: fcpci: Loaded. Dec 2 15:18:48 linux kernel: kcapi: notify up contr 1 Dec 2 15:18:48 linux kernel: capi: controller 1 up Dec 2 15:18:48 linux kernel: CSLIP: code copyright 1989 Regents of the University of California Dec 2 15:18:48 linux kernel: ISDN subsystem Rev: 1.108/1.92/1.134/1.77/1.21/1.5 loaded Dec 2 15:18:48 linux kernel: HiSax: Linux Driver for passive ISDN cards Dec 2 15:18:48 linux kernel: HiSax: Version 3.5 (module) Dec 2 15:18:48 linux kernel: HiSax: Layer1 Revision 2.39 Dec 2 15:18:48 linux kernel: HiSax: Layer2 Revision 2.23 Dec 2 15:18:48 linux kernel: HiSax: TeiMgr Revision 2.15 Dec 2 15:18:48 linux kernel: HiSax: Layer3 Revision 2.14 Dec 2 15:18:48 linux kernel: HiSax: LinkLayer Revision 2.47 Dec 2 15:18:48 linux kernel: HiSax: Approval certification valid Dec 2 15:18:48 linux kernel: HiSax: Approved with ELSA Microlink PCI cards Dec 2 15:18:48 linux kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI cards Dec 2 15:18:48 linux kernel: HiSax: Approved with Sedlbauer Speedfax + cards Dec 2 15:18:48 linux kernel: HiSax: Total 1 card defined Dec 2 15:18:48 linux kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) Dec 2 15:18:48 linux kernel: HiSax: AVM PCI driver Rev. 1.17 Dec 2 15:18:48 linux kernel: HiSax: AVM Fritz PnP/PCI config port b400-b41f already in use Dec 2 15:18:48 linux kernel: HiSax: Card AVM Fritz PnP/PCI not installed ! Dec 2 15:18:48 linux kernel: ISDN-subsystem unloaded ------------------ danke -- bis dann armin Sent through GMX FreeMail - http://www.gmx.net
armin brueckmann wrote:
moin
ich habe eine pci fritzkarte und bekomme sie bei suse7prof nicht ans laufen. ich hänge mal einige auszüge aus logfiles an. vielleicht hilt das ja weiter. ansonsten kann ich noch sagen das ich eine netzwerkkarte mit einem 10er netz beglückt habe und die isdn karte wird standartmäßig mit 192(?)er netz versorgt. kann es auch daran liegen?? danke für eure hilfe
Die IP-Adressen sind es definitiv nicht. Der folgende Eintrag weist aber ziemlich deutlich auf ein Konfigurationsproblem hin:
warn: Dec 2 15:18:48 linux kernel: HiSax: AVM Fritz PnP/PCI config port b400-b41f already in use
Hast Du die Parameter in der Konfigurationsdatei richtig eingestellt? Für AVM Fritz!Card, PCI-Version: I4L_TYPE_1="27" I4L_IRQ_1="" I4L_IO_1="" I4L_MEMBASE_1="" I4L_IO0_1="" I4L_IO1_1="" I4L_IO2_1="" Bei IRQ und IO darf nichts eingetragen werden, sonst will der Treiber eine Fritz!Card PnP (ISA!) ansprechen. Die findet er sicher nicht. Möglicherweise aber stattdessen die AWE64 (ISA PnP!).
Dec 2 15:18:48 linux kernel: HiSax: Card AVM Fritz PnP/PCI not installed ! Dec 2 15:18:58 linux kernel: isapnp: Card 'Creative SB AWE64 PnP' Dec 2 15:18:58 linux kernel: isapnp: 1 Plug & Play card detected total
Hoffe, geholfen zu haben. Georg
Hallo, anscheinend versuchst du, die AVM-Treiber und i4l gleichzeitig zu starten.
warn: Dec 2 15:18:48 linux kernel: HiSax: AVM Fritz PnP/PCI config port b400-b41f already in use Dec 2 15:18:48 linux kernel: HiSax: Card AVM Fritz PnP/PCI not installed ! Dec 2 15:18:58 linux kernel: isapnp: Card 'Creative SB AWE64 PnP' Dec 2 15:18:58 linux kernel: isapnp: 1 Plug & Play card detected total
messages: Dec 2 15:18:45 linux syslogd 1.3-3: restart. Dec 2 15:18:48 linux kernel: CAPI-driver Rev 1.18 : loaded Dec 2 15:18:48 linux kernel: capifs: Rev 1.11 : loaded Dec 2 15:18:48 linux kernel: capi20: started up with major 68 Dec 2 15:18:48 linux kernel: kcapi: capi20 attached Dec 2 15:18:48 linux kernel: capi20: Rev1.40: started up with major 68 Dec 2 15:18:48 linux kernel: fcpci: AVM FRITZ!Card PCI driver, revision 0.0 Dec 2 15:18:48 linux kernel: fcpci: Loading... Dec 2 15:18:48 linux kernel: fcpci: Driver 'fcpci' attached to stack Dec 2 15:18:48 linux kernel: kcapi: driver fcpci attached Dec 2 15:18:48 linux kernel: fcpci: Auto-attaching... Dec 2 15:18:48 linux kernel: fcpci: Stack version 3.09-02 Dec 2 15:18:48 linux kernel: kcapi: Controller 1: fritz-pci attached Dec 2 15:18:48 linux kernel: kcapi: card 1 "fritz-pci" ready. Dec 2 15:18:48 linux kernel: fcpci: Loaded. Dec 2 15:18:48 linux kernel: kcapi: notify up contr 1 Dec 2 15:18:48 linux kernel: capi: controller 1 up Ok, hier hast du den Capi-Treiber von AVM f"ur deine Fritz PIC geladen. Deine ISDN-Karte wird auch erkannt. :-)
Wenn du du isdnctrl aus dem i4l-Paket benutzen willst, musst du vorher das Modul capidrv laden. Dann kannst du mit isdnctrl deine MSN etc. setzen. Du musst keinen HiSax-Treiber laden!!! 2. M"oglichkeit: Du benutzt nicht die AVM-Treiber (dann kannst du nicht faxen), sondern nur HiSax. Gru"s Lars
Hallo Armin, armin brueckmann wrote:
moin
ich habe eine pci fritzkarte und bekomme sie bei suse7prof nicht ans laufen. ich hänge mal einige auszüge aus logfiles an. vielleicht hilt das ja weiter. ansonsten kann ich noch sagen das ich eine netzwerkkarte mit einem 10er netz beglückt habe und die isdn karte wird standartmäßig mit 192(?)er netz versorgt. kann es auch daran liegen?? danke für eure hilfe
hast Du mal versucht die Karte über YAST zu installieren? Dort kannst Du, nachdem Du die Daten Deiner Karte (bei einer PCI ja nicht viel) eingegeben hast, durch "Starten" testen ob die Karte erkannt und gestartet wird. Sollten Fehler auftauchen wird zumindest schonmal die Richtung gezeigt wo der Fehler liegt. Damit habe ich sowohl meine alte Fritz Classic und jetzt neuerdings meine Sedelbauer PCI ohne Probleme installieren können. Gruß Thomas
-----Ursprüngliche Nachricht----- Von: armin brueckmann [mailto:news0@gmx.net] Gesendet: Samstag, 2. Dezember 2000 22:09 An: suse-isdn@suse.com Betreff: [suse-isdn] pci fritz will nicht
moin
ich habe eine pci fritzkarte und bekomme sie bei suse7prof nicht ans laufen. ich hänge mal einige auszüge aus logfiles an. vielleicht hilt das ja weiter. ansonsten kann ich noch sagen das ich eine netzwerkkarte mit einem 10er netz beglückt habe und die isdn karte wird standartmäßig mit 192(?)er netz versorgt. kann es auch daran liegen?? danke für eure hilfe ------------------
Hallo, ich habe auch eine Fritz PCI, kann aber sagen, daß die am unproblematischsten laüft. In Yast1 installieren I4l start X EsDss Protokoll oder wie das heißt AVM FRITZ PCI und das wars. Habe auch schon Fritz PNP, Fritz Classic und eine Teles 16.3 zum laufen bekommen. Da mußte ich rumprobieren, welcher IRQ, welche IO-Ports funken, aber Fritz PCI war problemlos. Eventuell wenn richtig installiert aber nicht läuft, anderen PCI-Slot probieren. Horst
participants (5)
-
armin brueckmann
-
Georg Gayer
-
Horst Grolms
-
Lars Mucha
-
Thomas Fick