Hallo, meine FritzCard scheint garnicht mehr funktionieren zu wollen. bis vor einer Woche bin ich noch zufrieden mit SuSE 9.0 gefahren und alles lief viele Monate super. Jetzt setzte ich den Rechner neu auf und kein DSL ;-( Hoffentlich kann mir jemand Helfen. Anbei ein paar systeminfos: von meinem dmesg... capidrv: Rev 1.1.2.2: loaded fcclassic: unsupported module, tainting kernel. fcclassic: AVM FRITZ!Card Classic driver, revision 0.6.2 fcclassic: (fcclassic built on Nov 17 2004 at 20:44:08) fcclassic: Driver 'fcclassic' attached to stack. (152) fcclassic: Stack version 3.11-02 kcapi: Controller 1: fcclassic-0300-07 attached kcapi: card 1 "fcclassic-0300-07" ready. capidrv: controller 1 up capidrv-1: now up (2 B channels) capidrv-1: D2 trace enabled fcdslsl: unsupported module, tainting kernel. fcdslsl: Base address: d1aca6f0 fcdslsl: Compile time: 20:43:44 fcdslsl: AVM FRITZ!Card DSL SL driver, revision 0.2.0 fcdslsl: (fcdslsl built on Nov 17 2004 at 20:43:44) PCI: Enabling device 0000:00:09.0 (0105 -> 0107) AMD756: dev 1244:2700, router pirq : 2 get irq : 11 PCI: Found IRQ 11 for device 0000:00:09.0 fcdslsl: Loading... fcdslsl: PCI: AVM FRITZ!Card DSL SL, dev 2700, irq 9 fcdslsl: data ea800000 (4M), code ef000000 (8M), mmio dc00 fcdslsl: I/O region at 0x0000dc00 fcdslsl: Controller data memory mapped to d1b80000 fcdslsl: Controller code memory mapped to d4800000 kcapi: Controller 2: fcdslsl-dc00-9 attached fcdslsl: Controller 2 (2) --> 1 fcdslsl: Loaded. fcdslsl: PCI driver registered. fcdslsl: CAPI driver registered. fcclassic: Cannot handle two controllers! fcdslsl: Loaded 315520 bytes of firmware. fcdslsl: Initializing device structures... fcdslsl: Using VCC/VPI/VCI = 0x1/0x1/0x20 fcdslsl: Version string #0 rejected. fcdslsl: Version string #1: fcdslsl: Library version: 3.11-03 fcdslsl: Card type: A1 fcdslsl: Capabilities: Add. Service: V.42bis, Fax G3 Polling, DTMF, GSM, CAPI 1.1 fcdslsl: D-channel protocol: DSS1 fcdslsl: Returning requirements, TX 8/300/284, RX 8/844/812 fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr c12fe400, paddr 012fe400, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr cfe11200, paddr 0fe11200, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr c12f6800, paddr 012f6800, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr cfd40e00, paddr 0fd40e00, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr c12fce00, paddr 012fce00, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr c12fc800, paddr 012fc800, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr cfd46600, paddr 0fd46600, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: Allocating DMA buffer of 300 bytes fcdslsl: Allocated DMA buffer vaddr c126fc00, paddr 0126fc00, length 300 fcdslsl: ... is a TX DMA buffer fcdslsl: DMA context of structure #0(c93663f0) set to c9366470 fcdslsl: DMA context of structure #1(c9366470) set to c93664f0 fcdslsl: DMA context of structure #2(c93664f0) set to c9366570 fcdslsl: DMA context of structure #3(c9366570) set to c93665f0 fcdslsl: DMA context of structure #4(c93665f0) set to c9366670 fcdslsl: DMA context of structure #5(c9366670) set to c93666f0 fcdslsl: DMA context of structure #6(c93666f0) set to c9366770 fcdslsl: DMA context of structure #7(c9366770) set to c93663f0 fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr cf2d0c00, paddr 0f2d0c00, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr ce28b000, paddr 0e28b000, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr ce28b400, paddr 0e28b400, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr ce28b800, paddr 0e28b800, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr ce28bc00, paddr 0e28bc00, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr cecd9000, paddr 0ecd9000, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr cecd9400, paddr 0ecd9400, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: Allocating DMA buffer of 844 bytes fcdslsl: Allocated DMA buffer vaddr cecd9800, paddr 0ecd9800, length 844 fcdslsl: ... is a RX DMA buffer fcdslsl: DMA context of structure #8(c93667f0) set to c9366870 fcdslsl: DMA context of structure #9(c9366870) set to c93668f0 fcdslsl: DMA context of structure #10(c93668f0) set to cb48d670 fcdslsl: DMA context of structure #11(cb48d670) set to c9366af0 fcdslsl: DMA context of structure #12(c9366af0) set to c9366ab0 fcdslsl: DMA context of structure #13(c9366ab0) set to c9366b70 fcdslsl: DMA context of structure #14(c9366b70) set to c9366bf0 fcdslsl: DMA context of structure #15(c9366bf0) set to c93667f0 fcdslsl: IRQ #9 assigned to fcdslsl driver. fcdslsl: No debug buffer. fcdslsl: I/O window has been set! fcdslsl: Loadfile based reset. fcdslsl: /usr/src/packages/BUILD/kernel-default-2.6.8/modules-2.6.8/fcdsl/src/src.fcd slsl/lib.c(364): info (msec > 9) failed fcdslsl: /usr/src/packages/BUILD/kernel-default-2.6.8/modules-2.6.8/fcdsl/src/src.fcd slsl/lib.c(364): info (msec > 9) failed fcdslsl: /usr/src/packages/BUILD/kernel-default-2.6.8/modules-2.6.8/fcdsl/src/src.fcd slsl/lib.c(364): info (msec > 9) failed fcdslsl: Firmware does not respond! fcdslsl: Loadfile based reset. fcdslsl: Freeing TX DMA buffer vaddr c12fe400 fcdslsl: Freeing TX DMA buffer vaddr cfe11200 fcdslsl: Freeing TX DMA buffer vaddr c12f6800 fcdslsl: Freeing TX DMA buffer vaddr cfd40e00 fcdslsl: Freeing TX DMA buffer vaddr c12fce00 fcdslsl: Freeing TX DMA buffer vaddr c12fc800 fcdslsl: Freeing TX DMA buffer vaddr cfd46600 fcdslsl: Freeing TX DMA buffer vaddr c126fc00 fcdslsl: Freeing RX DMA buffer vaddr cf2d0c00 fcdslsl: Freeing RX DMA buffer vaddr ce28b000 fcdslsl: Freeing RX DMA buffer vaddr ce28b400 fcdslsl: Freeing RX DMA buffer vaddr ce28b800 fcdslsl: Freeing RX DMA buffer vaddr ce28bc00 fcdslsl: Freeing RX DMA buffer vaddr cecd9000 fcdslsl: Freeing RX DMA buffer vaddr cecd9400 fcdslsl: Freeing RX DMA buffer vaddr cecd9800 fcdslsl: Error while starting protocoll stack! fcdslsl: Resetting device structures... fcdslsl: Reset done. fcdslsl: Deinitializing device... dann von capiinfo ohne dsl: Number of Controllers : 1 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-02 (49.18) Serial Number: 1000001 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation supported (leased lines) B1 protocols support: 0x4000011f 64 kbit/s with HDLC framing 64 kbit/s bit-transparent operation V.110 asynconous operation with start/stop byte framing V.110 synconous operation with HDLC framing T.30 modem for fax group 3 Modem asyncronous operation with start/stop byte framing B2 protocols support: 0x00000b1b ISO 7776 (X.75 SLP) Transparent LAPD with Q.921 for D channel X.25 (SAPI 16) T.30 for fax group 3 ISO 7776 (X.75 SLP) with V.42bis compression V.120 asyncronous mode V.120 bit-transparent mode B3 protocols support: 0x800000bf Transparent T.90NL, T.70NL, T.90 ISO 8208 (X.25 DTE-DTE) X.25 DCE T.30 for fax group 3 T.30 for fax group 3 with extensions Modem 0100 0200 39000000 1f010040 1b0b0000 bf000080 00000000 00000000 00000000 00000000 00000000 00000000 01000001 00020000 00000000 00000000 00000000 Supplementary services support: 0x000003ff Hold / Retrieve Terminal Portability ECT 3PTY Call Forwarding Call Deflection MCID CCBS dann mit dsl: Number of Controllers : 2 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-02 (49.18) Serial Number: 1000001 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation supported (leased lines) B1 protocols support: 0x4000011f 64 kbit/s with HDLC framing 64 kbit/s bit-transparent operation V.110 asynconous operation with start/stop byte framing V.110 synconous operation with HDLC framing T.30 modem for fax group 3 Modem asyncronous operation with start/stop byte framing B2 protocols support: 0x00000b1b ISO 7776 (X.75 SLP) Transparent LAPD with Q.921 for D channel X.25 (SAPI 16) T.30 for fax group 3 ISO 7776 (X.75 SLP) with V.42bis compression V.120 asyncronous mode V.120 bit-transparent mode B3 protocols support: 0x800000bf Transparent T.90NL, T.70NL, T.90 ISO 8208 (X.25 DTE-DTE) X.25 DCE T.30 for fax group 3 T.30 for fax group 3 with extensions Modem 0100 0200 39000000 1f010040 1b0b0000 bf000080 00000000 00000000 00000000 00000000 00000000 00000000 01000001 00020000 00000000 00000000 00000000 Supplementary services support: 0x000003ff Hold / Retrieve Terminal Portability ECT 3PTY Call Forwarding Call Deflection MCID CCBS Controller 2: Manufacturer: 1000001 CAPI Version: 808464433.3223600 Manufacturer Version: 49.18 Serial Number: 1000001 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation supported (leased lines) B1 protocols support: 0x4000011f 64 kbit/s with HDLC framing 64 kbit/s bit-transparent operation V.110 asynconous operation with start/stop byte framing V.110 synconous operation with HDLC framing T.30 modem for fax group 3 Modem asyncronous operation with start/stop byte framing B2 protocols support: 0x00000b1b ISO 7776 (X.75 SLP) Transparent LAPD with Q.921 for D channel X.25 (SAPI 16) T.30 for fax group 3 ISO 7776 (X.75 SLP) with V.42bis compression V.120 asyncronous mode V.120 bit-transparent mode B3 protocols support: 0x800000bf Transparent T.90NL, T.70NL, T.90 ISO 8208 (X.25 DTE-DTE) X.25 DCE T.30 for fax group 3 T.30 for fax group 3 with extensions Modem 0100 0200 39000000 1f010040 1b0b0000 bf000080 00000000 00000000 00000000 00000000 00000000 00000000 01000001 00020000 00000000 00000000 00000000 FAC GET - Info: Illegal Controller / PLCI / NCCI (0x2002) häää was heist da illegal controller... hab ich im Saturn gekauft!!! ;-) dann lspci -v 0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller (rev 25) Flags: bus master, medium devsel, latency 120 Memory at e8000000 (32-bit, prefetchable) Memory at eadff000 (32-bit, prefetchable) [size=4K] I/O ports at da00 [disabled] [size=4] Capabilities: [a0] AGP version 1.0 0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP Bridge (rev 01) (prog-if 00 [Normal decode]) Flags: bus master, 66Mhz, medium devsel, latency 120 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: eae00000-eeefffff Prefetchable memory behind bridge: e2400000-e64fffff Expansion ROM at 0000c000 [disabled] [size=4K] 0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ISA (rev 01) Flags: bus master, medium devsel, latency 0 0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-756 [Viper] IDE (rev 07) (prog-if 8a [Master SecP PriP]) Flags: bus master, medium devsel, latency 32 I/O ports at f000 [size=16] 0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ACPI (rev 03) Flags: medium devsel 0000:00:07.4 USB Controller: Advanced Micro Devices [AMD] AMD-756 [Viper] USB (rev 06) (prog-if 10 [OHCI]) Flags: bus master, medium devsel, latency 16, IRQ 9 Memory at efffe000 (32-bit, non-prefetchable) 0000:00:09.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!Card DSL SL (rev 01) Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH Fritz!Card DSL SL Flags: bus master, medium devsel, latency 128, IRQ 9 Memory at ea800000 (32-bit, prefetchable) [disabled] Memory at ef000000 (32-bit, non-prefetchable) [disabled] [size=8M] I/O ports at dc00 [size=16] Capabilities: [40] Power Management version 2 0000:00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30) Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 Flags: bus master, medium devsel, latency 128, IRQ 9 I/O ports at de00 [size=effc0000] Memory at efffff80 (32-bit, non-prefetchable) [size=128] Expansion ROM at 00020000 [disabled] Capabilities: [dc] Power Management version 1 0000:01:05.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA]) Subsystem: 3Dfx Interactive, Inc. Voodoo3 AGP Flags: 66Mhz, fast devsel, IRQ 11 Memory at ec000000 (32-bit, non-prefetchable) [size=eeef0000] Memory at e4000000 (32-bit, prefetchable) [size=32M] I/O ports at cc00 [size=256] Expansion ROM at 00010000 [disabled] Capabilities: [54] AGP version 1.0 Capabilities: [60] Power Management version 1 lsmod zeigt beide treiber (module) in memory fcdslsl 792036 0 fcclassic 496024 2 und auch ohne fcclassic funkioniert das Zeugs nicht. Unter 9.0 aber schon.... na hoffentlich kann mir jemand helfen... find SuSE super! Gruß an alle, Elkin ohh... capi.conf sieht so aus: #SuSEconfig.isdn generated # card file proto io irq mem cardnr options fcclassic - - 0x300 7 - 1 fcdslsl fdssbase.bin - - - - 1