# $Id: zyxel-1496e,v 1.1.1.1 1998/10/12 20:47:48 root Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a ZyXEL U1496.  Firmware revisions from
# 5.02 on should work, though rev 6.01 works much better. 
# Actually, the preferred use is to get firwmare rev 6.13 or
# 6.14 and configure the modem to use Class 2.0; this file
# is kept around for folks with old firmware.
#
# This configuration file sets up the ZyXEL to run at 38.4 for
# both sending and receiving.  RTS/CTS flow control is used on
# the tty port--you probably shouldn't use XON/XOFF.  Note that
# on an SGI system the getty speed is the following non-standard
# gettydefs entry:
#
# dx_38400# B38400 # B38400 SANE TAB3 HUPCL #\r\n\n$HOSTNAME login: #dx_38400
#
#
CountryCode:		49
AreaCode:		30
FAXNumber:		+49.**.************
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		527
SessionTracing:		527
RecvFileMode:		0644
LogFileMode:		0600
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-r -b -s %s %l"
LocalIdentifier:	"Elsner"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
NoCarrierRetrys:	3
MaxRecvPages:		30
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400		# 38.4 works fine
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&H0		# disable flow control
ModemHardFlowCmd:	AT&H3		# hardware flow control
ModemSoftFlowCmd:	AT&H4		# software flow control
ModemSetupDTRCmd:	AT&D2		# DTR off causes modem to hang up
ModemSetupDCDCmd:	AT&C1		# DCD tracks carrier
ModemSetupAACmd:	AT+FAA=1	# enable in current class
#
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
Class2RecvDataTrigger:	"\022"		# a la 2388-B
#
# Additional reset commands:
#
# &B1	  DTE-DCE rate is fixed at DTE setting
# &N0	  Auto-negotiate highest possible DCE-DCE link rate
# &S0	  DSR always on
# *F0	  Deny remote configuration
# S18=2	  Receive at 38400
# S38.3=1 DCD on/off sequence follows UNIX standard; also
#	  fix receiving baud rate at S18 value
# S39=0	  (avoid Class 2 compatibility hacks)
# 
ModemResetCmds:		AT&B1&N0&S0*F0S18=2S38.3=1S39=0
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# Unfortunately, ZyXEL's don't seem to detect a busy signal when
# the @ symbol is used to terminate the dialing string.  Instead
# calls to a busy line come back with a NO CARRIER status which
# causes us to toss the job.  Consequently we fall back to the
# normal method and raise the number of retries on a no carrier
# status.  ZyXEL claims that this behaviour is not a bug, but 
# rather that we are requesting ``an enhancement'' (never mind
# that their manual says that it should work).
#
ModemDialCmd:		ATX3DT%s	# no '@' 'cuz then busy not recognized
NoCarrierRetrys:	3		# retry 3 times on no carrier
#
ModemSetVolumeCmd:	"ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#QualifyCID:		etc/cid		# CID access control list file
#CIDNumber:		"CALLER NUMBER: " # pattern string for phone number info
#CIDName:		"CALLER NAME: "	# pattern string for identity info
#
PagerSetupCmds:		AT&K0&N15	# use V.22 at 1200 bps (PageNet)
#
# Rev 6.1x firmware have a bug in the ECM support so
# explicitly disable it's use.  To re-enable its use just
# comment out the following line.
#
Class2DCCQueryCmd:	"!(0,1),(0-5),(0-4),(0-2),(0,1),(0),(0),(0-7)"