[opensuse-factory] network disabled after networkinstallation in B5
Just a quick question. Yesterday night just before i dashed off going home, i did a fresh install (not an update) of B5 on a HP-DL320. Everything installed smoothly (at least two of my issues are solved eg unreadable fields while partitioning and missing yast2-schema). However after installing, networks seems dead. a) installation is done via pxe and a local install-server b) "ethtool eth0" indicates that cable is plugged in. c) after rebooting the system got its ip-address via DHCP (!!) These three indicate a working network d) firewall is "full open", for ipv4 and ipv6 e) tcpdump showd only outgoing traffic (looked just for a short while, but on busy network) f) ping to my dhcp-server, default-gw, dns-aerver failed. g) no such problem in 11.1-beta4 h) realtek-chipset afair, (no intel ;-) Any simular experiences? If so, any remedies? If not, i'll investigate next week further, and do the bugzilla-tour hw -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-factory+help@opensuse.org
2008/11/15 Hans Witvliet
Just a quick question.
Yesterday night just before i dashed off going home, i did a fresh install (not an update) of B5 on a HP-DL320.
Everything installed smoothly (at least two of my issues are solved eg unreadable fields while partitioning and missing yast2-schema).
However after installing, networks seems dead. a) installation is done via pxe and a local install-server b) "ethtool eth0" indicates that cable is plugged in. c) after rebooting the system got its ip-address via DHCP (!!) These three indicate a working network d) firewall is "full open", for ipv4 and ipv6 e) tcpdump showd only outgoing traffic (looked just for a short while, but on busy network) f) ping to my dhcp-server, default-gw, dns-aerver failed. g) no such problem in 11.1-beta4 h) realtek-chipset afair, (no intel ;-)
Any simular experiences? If so, any remedies? If not, i'll investigate next week further, and do the bugzilla-tour
I installed beta 4 and after the setup of a dsl connection, i can't connect to to any site, because the dns resolution do'nt works. I configured the dsl connection with the networkmanager, and after restarting the system, the problem continues. Regards -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-factory+help@opensuse.org
On Sat, 2008-11-15 at 14:22 +0100, Hans Witvliet wrote:
Just a quick question.
Yesterday night just before i dashed off going home, i did a fresh install (not an update) of B5 on a HP-DL320.
Everything installed smoothly (at least two of my issues are solved eg unreadable fields while partitioning and missing yast2-schema).
However after installing, networks seems dead. a) installation is done via pxe and a local install-server b) "ethtool eth0" indicates that cable is plugged in. c) after rebooting the system got its ip-address via DHCP (!!) These three indicate a working network d) firewall is "full open", for ipv4 and ipv6 e) tcpdump showd only outgoing traffic (looked just for a short while, but on busy network) f) ping to my dhcp-server, default-gw, dns-aerver failed. g) no such problem in 11.1-beta4 h) realtek-chipset afair, (no intel ;-)
Any simular experiences? If so, any remedies? If not, i'll investigate next week further, and do the bugzilla-tour
Still in RC1, reported as 450303 Work around: /etc/rc.d/after.local with ifconfig eth0 down ifconfig eth0 up mount -a -t nfs might (!) be xen related hw -- To unsubscribe, e-mail: opensuse-factory+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-factory+help@opensuse.org
participants (2)
-
Hans Witvliet -
Juan Erbes